11.7 A concrete pile 15.24 m long having a cross section of 406 mm × 406 mm isfully embedded in a saturated clay layer for which ya = 19.02 kN/m². = 0.and c, = 76.7 kN/m². Determine the allowable load that the pile can carry. (Let FS= 3.) Use the a method to estimate the skin friction and Veric's method for pointload estimation.

Answered: Image /qna-images/answer/090b2b0c-6764-4b1c-bd9d-a2f9da591ce5.jpg

7 A concrete pile 15.24 m long having a cross section of 406 mm x 406 mm is fully embedded in a saturated clay layer for which y= 19.02 kN/m', = 0. and c, = 76.7 kN/m². Determine the allowable load that the pile can carry. (Let F 3.) Use the a method to estimate the skin friction and Veric's method for point %3D Joad estimation

7 A concrete pile 15.24 m long having a cross section of 406 mm x 406 mm is fully embedded in a saturated clay layer for which y= 19.02 kN/m', = 0. and c, = 76.7 kN/m². Determine the allowable load that the pile can carry. (Let F 3.) Use the a method to estimate the skin friction and Veric's method for point %3D Joad estimation

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In Hiley’s formula for driven piles i.e. R=E/(s+0.5c), why is a coefficient of 0.5 applied for the term elastic deformation of piles and soil?
Determine the length, L, required to support the load as in Figure below. The diameter of the pile is 450 mm. A factor of safety of 3 is required. Use Meyerhof’s method for calculating load carrying capacity of the pile point and α method to calculate friction resistance capacity.
Please explain this problem and solution step by step
PROB 3 A square prestressed concrete pile having a size of 36 cm is to be driven in a layer of clay soil. The design capacity of the pile is 360 kN with a factor of safety of 2.
FDE 016: A prestressed concrete pile, 400 mm x 400 mm in cross-section, is to be driven in a clayey soil as shown. Use alpha method with factor of safety of 2. Soft Clay 17-15.7 kN/m² c=32 kPa 8 m Stiff Clay * = 19 kN/m² Cu = 90 kPa = 0.5 Refer to FDE 016. What is the end bearing capacity of pile in KN? Select the correct response: 251.84 184.25 129.60 245.32 6 m.
I need detailed explanation to solve the exercise below. There are some formulas and hints, I also added some tables from the book.Meyerhof's method, Coyle and Castello's method and Vesic's method were already solved.
1. Design the cantilever sheet pile wall supporting a loose sand fill as shown in the following Figure. The surcharge is equal to 10 kPa. GWT is at the same height on both sides, and assume yw=10kN/m³. Based on the log spiral solutions, the Ka for the loose sand is 0.3 while the Ka and Kp for the dense sand are 0.2 and 13.125, respectively. a) For a factor of safety of 2 on the passive resistance, determine the required depth of penetration depth, D. (initial trial with D'=4.2m) b) Determine the bending moment of the sheet pile. c) Select a sheet pile section from the Table 9.1 (E=210x10³ MN/m² and fall=210 MN/m²)
Please do 12,21
Check the pile load of the Railroad Bridge of (hilla) for 4000 KN with pile diameter (1 m). The depth of ‎bored pile is (15 m) .The ground water level is about (2.5 mm) from the natural ground level .The details of ‎layers . (density of soil= 18.5 kN /m3 , Cu= 25 kPa) (Note: ‎α = 1.0 for clay with Cu ≤ 25 kPa , α = 0.5 for clay with Cu ≥ kPa KN/m2 .‎ *
Determine the diameter of 70 ft long pile driven in the medium dense sand (Shown in Figure). Design load is 185Kips and factor of safety can be assumed to be 2.5. Frictional coefficient is 0.45 Sand y = 115lb/ft3 Ø = 28° K = 0.80 30 %3D Sand 128lb/ft %3! Ysat Ø= 30° K = 0.85 33°C 70
I need detailed explanation to solve the exercise below. There are some formulas and hints, I also added some tables from the book.Meyerhof's method, Coyle and Castello's method and Vesic's method were already solved.
Question A pile of 0.50 m diameter and of length 10 m is embedded in a deposit of clay. The undrained strength parameters of the clay are cohension = 60 kN/m2 and the angle of internal friction = 0. The skin friction capacity (kN) of the pile for an adhesion factor of 0.6, is 77