630 cm^3/s Water at 320 k is PumPed in a 40 mm (id) through a length of 150m in horizontal direction and up through avertical height of 10m. in the Pipe there is a control Valve which may be taken as equivelent to 200 Pipe diameter and also there is other Pipe fitting equivelent to 60d. if the main Pipe has a roughness of 0.0002m. what a power of PumP if It's efficiency is 60% And the viscosity is 0.00065 pa.s

630 cm^3/s Water at 320 k is PumPed in a 40 mm (id) through a length of 150m in horizontal direction and up through avertical height of 10m. in the Pipe there is a control Valve which may be taken as equivelent to 200 Pipe diameter and also there is other Pipe fitting equivelent to 60d. if the main Pipe has a roughness of 0.0002m. what a power of PumP if It's efficiency is 60% And the viscosity is 0.00065 pa.s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

FLUID MECHANICS!!! TY!
I need the answer as soon as possible
Note: Don't copy from Chegg.
A 300mm x 300mm pipe discharges 600 L/s of water where the length is 30m. Determine the head loss if f = 0.021 hf = 83.412m hf = 72.126m hf = 86.246m No answer among the choices hf = 68.921m hf = 77.093m
Due in 2 hrs Please show figure thanks! No figure no credit for us in school.
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
A 30-cm by 15-cm Venturi meter is mounted on a vertical pipe with the flowupward. One hundred twenty-six (126) liters per second of oil (s.g. = 0.80)flows through the pipe. The throat section is 15cm above the upstreamPage 2 of 3section. If Cv=0.957, what is the difference in pressure between the inlet andthe throat?
7. Barometeric pressure is 101.3 kPa and vapor pressure of water is 32.4 kPa. Calculate the elevation (in meters) of the tubing end 3 for maximum flowrate through this pipeline. Also sketch the energy line, EL (color red) and the hydraulic grade line, HGL (color blue) on the drawing for this situation. El. 34 Water 150 mm d EI. 30.5
5. ol with sp. gr. of 0.88 is being pumped frem a lower reservolr to an elevated tank The pump In the system is 65% efflelent and Is rated at 160kW. Determine the flow rate of the oll in the pipe if the total head los (rom point 1 to point 2 is 5.5m of oll. 150m 200-mm Pump Elev 160m Elev. 150 m
DT. Asmaa Abdul Jabbar Q2: Water flow from B to A, if real power of pump =175kw, with efficiency 85%. (neglect minor losses) Find: Discharge at each pipe. Pipe No. L (km) D (cm) f 0.018 1 0.5 15 2 0.55 20 0.02 EL.25m A P 1 2 EL.100m B
A 1 m diameter new cast iron pipe 800 m long and has a head loss of 1.11m. Find the discharge in Lit/sec if C=130.90 Group of answer choices 890.14 918.40 980.41 809.41