60 m 390 mm 600 mm Q-2 Q-2: If the 280-kg drum has a center of mass at point G, determine the horizontal and vertical components of force acting at pin A and the reactions on the smooth pads C and D. The grip at B on member DAB resists both horizontal and vertical components of force at the rim of the drum.

60 m 390 mm 600 mm Q-2 Q-2: If the 280-kg drum has a center of mass at point G, determine the horizontal and vertical components of force acting at pin A and the reactions on the smooth pads C and D. The grip at B on member DAB resists both horizontal and vertical components of force at the rim of the drum.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.9P: The four-bar linkage supports the homogeneous box of weight W. Neglecting the weight of the linkage,...

See similar textbooks

Similar questions

The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
The 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed. Determine the force P and the roller reactions at A and B.
The two uniform cylinders, each of weight W, are resting against inclined surfaces. Neglecting friction, draw the free-body diagrams for each cylinder and for the two cylinders together. Count the total number of unknowns and the total number of independent equilibrium equations.
The four-bar linkage supports the homogeneous box of weight W. Neglecting the weight of the linkage, determine the horizontal pin reactions at A and B.
Consider the following system in static equilibrium. Force vector Facts at a distance from the pin support at point O. Draw appropriate FBD as necessary. Assume frictionless pulleys If the reaction forces at O is zero and magnitude F is 169N, a. Find F and "a". (F need not necessarily be in the 4 quadrant as shown below) b. Find reaction forces at B. 4m Im 5m 12
The 40-kg uniform triangular plate is supported by two small hinges A and B and the cable system shown. For the horizontal position of the plate, determine all hinge reactions and the tension T in the cable. Hinge A can resist axial thrust, but hinge B cannot. See Table D/3 in Appendix D for the mass-center location of a triangular plate. Answers: Ax= Ay- A₂ 0.43 m 0.20 m By B₂= 0.20 m 0.43 m T= 0.91 m. Z Z N N z z N N N N 1.30 m
The mass center G of the 1400-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. 1386 mm 964 mm
The 46-kg homogeneous smooth sphere rests on the 42° incline A and bears against the smooth vertical wall B. Calculate the contact force at A and B. Assume 0 = 42°. B A Answers: FA = FB = N
Current Attempt in Progress The mass center G of the 1530-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. Answers: GO -1335 mm-982 mm Normal force under each of the front tires: Nf= Normal force under each of the rear tires: N₁ = i i N N
The system shown is in equilibrium by the applied 250 N-force. Determine the pin reaction D. Neglect the small force of the light return spring C and friction 100 15° 250 N 100 85 D. 25 225 -50- Dimensions in millimeters
Problem 1: The The uniform 30-kg ventilation door OAP is opened by the mechanism shown. Plot the required force in the cylinder DE as a function of the door opening angle over the range 0 ses 0max, where 8max is the maximum opening. Determine the minimum and maximum values of this force and the angles at which these extremes occur. Note that the cylinder is not horizontal when e = 0. - 275 - 525 B 300 100 350 - 400- AB = 300 CD = DB = 150 Dimensions in millimeters
The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is a 200-kg pebble in the bucket, with center of mass at G2 determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader. L0.5 m E 0.1 m_ D 0.2 m G2 0.18 m G1 0.6 m 0.5 m В 0.45 m 1.2 m 0.15 m 0.2 m 0.05 m Figure Q3