60 lb/ft - 3 ft - 12 ft

Q: Q2. A beam has cross-section as shown in Fig. If the shear force acting on this is 25 kN, draw the…

A: Givenshear force=25Kn

Q: Calculate the resultant internal loadings on the cross section at point M (Figure 1)

A:

Q: Determine the shear stress at points A and B if the beam is subjected to a shear force of V = 600…

A: Given data: Shear force V = 600 Kn   Drawing the cross-section of the beam: Calculating moment of…

Q: Aceite Sg 0,86 4 m 0.5 m Longitud: 6 m.

A:

Q: the bar element's linear shape, or interpolation ons are: N1= 1-x/L, and N2= x/L (where L is the ent…

A:

Q: 1-22. The floor crane is used to lift a 600-kg concrete pipe. Determine the resultant internal…

A: Solution:

Q: The beam AB is pin supported at 4 and supported by a cable BC. Determine the resultant internal…

A: Solution:

Q: The brace and drill bit is used to drill a hole at O. If the drill bit jams when the brace is…

A: considering free body diagram of the system 1 in = 0.0833333ft considering all dimensions in ft.…

Q: Determine the maximum shear (k) at the given structure. 10 k 0.8 k/ft 8 k |C B. ton -6 ft -12 ft- 12…

A: Given data: w=0.8 k/ft Need to determine the value of maximum shear force.

Q: Determine the resultant of the line load acting on the beam ABC. 1200 Ib/ft y 1700 Ib/ft C 6 ft -8…

A: find the resultant force of the given distributed load.

Q: If the built-up beam is subjected to an internal moment of M = 75 kN # m, determine the amount of…

A:

Q: A C B - 3 ft -- 12 ft

A:

Q: constant throughout the length. ns. Draw the FBD of the beam with the calculated values of the…

A: Given data Point load = 250 kN Distributed load = 75 kN/m Solution are given below

Q: Determine the total area of the cross-section (in sg m) without disregarding the areas in the end…

A:

Q: •1-5. Determine the resultant internal loadings in the beam at cross sections through points D and…

A:

Q: 1-23. The pipe has a mass of 12 kg/m. If it is fixed to the wall at A, determine the resultant…

A:

Q: The beam AB is pin supported at 4 and supported by a cable BC. Determine the resultant internal…

A:

Q: The boom DF of the jib crane and the column DE have a uniform weight of 50 lb>ft. If the…

A:

Q: 1-3. The beam AB is fixed to the wall and has a uniform weight of 80 lb/ft. If the trolley supports…

A:

Q: The internal shear at the left end is Take P 2 kN. P. P. BI a L/3- O 2 kN O none of them. O -2 kN

A: Given: P=2 kN

Q: 1. Determine the vertical displacement of section C. El and EA are all constants. F a В 1/2 1/2

A: given data: lenth of BD=a

Q: 7-9. Determine the resultant internal loading on the cross section through point D of the pliers. 20…

A: Resolving Forces at D: Σ FY = 0FDy-20Cos30 = 0FDy = 17.3205 NΣ FX = 0FDX-20 Sin 30=0FDy=10 NΣ M =…

Q: The beam supports the distributed load shown.  Determine the resultant internal loadings acting on…

A: Given simply supported  as shown below

Q: 1-27. The pipe has a mass of 12 kg/m. If it is fixed to the wall at A, determine the resultant…

A:

Q: W 6 ft D -4 ft- + B -4 ft- C I Determine the normal force at point b using method of section if w =…

A:

Q: ne the shear force Vin the beam at the point located 2 kN/m 3 m 4.70 kN 5 kN/m {]]]] 5 m 14.30 kN

A:

Q: (Q2-a) The steel beam has the cross-sectional area shown. If w = 5 kip\ft, determine the absolute…

A: Given    Load, P = 5 kip/ft Length, L = 24 ft Find  Maximum bending stress

Q: 1-19. Determine the resultant internal loadings acting on the cross section through point C. Assume…

A:

Q: If M=2.5kip.ft, determine the magnitute of the resultant force the bending stresses produce on the…

A:

Q: The bar has a cross-sectional area of 400(10−6) m2. If it is subjected to a uniform axial…

A: Given: The cross-sectional area of the bar, A = 400x10-6 m2   Force equilibrium in x-direction, The…

Q: 1. The intensity of the shear stress distribution acting over the cross sectional area needs to be…

A:

Q: 5. Determine the internal loadings acting 6 kN at the cross-section that contains 0.75 m point B.…

A: Given data: Vertical force = 6 kN Need to determine the internal loadings acting at the…

Q: The blade of the hacksaw is subjected to a pretension force of F = 100 N. Determine the resultant…

A: Draw a diagram for the problem showing the right side of the cross-section b-b and resolve the force…

Q: thin-walled tube is subjected to torsion as shown. Determine the Area bounded by the median lin =30

A: Givenr=300mmθ=80°L=6m

Q: 4 kN/m 3 m -15m -15m-

A:

Q: The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to…

A: Consider the free body diagram of shaft AB as shown below.

Q: The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of…

A: Given data: Axial load subjected on the pipe, P = 60 kN. The inner diameter of the pipe, di = 30…

Q: y - 4 m - 6 m 15 kN/m -10 kN/m

A:

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Determine…

A: Let us draw the all the reactions forces

Q: *1-4. Determine the resultant internal loadings in the beam at cross sections through points D and…

A: Take section BC: take the moment about point B: ΣMB=0RC×16-16×8=0RC=8 kipand RB+RC=16 kipRB=16-8=8…

Q: Q3- Find H and the pressure gage P as shown in Fig. 125 mm d H 75 mm d 175 mm 100 mm d Hg (13.57)

A:

Q: Q1/ In each case, draw the estimated elastic curve: -4 m- 8 kN.m 2 kN/m 8 kN 4 kN

A:

Q: Determine the shear stress (in Mpa) in the 27.99-mm-diameter pin at A that support the beam if P =…

A:

Q: If the extended stress at the pointpin the level and at n= 1+j+ k is given by matrix 10 2 222 the…

A:

Q: Determine the resultant internal loadings acting on the cross-section at B ofthe pipe shown in Fig.…

A: Free body diagram of part 'AB' of the pipe is taken in to account here. So, load acting at 'A' in…

Q: The rod is subjected to an external axial force of 800 N and a uniform distributed load of 100…

A: givenexternal axial force Fa=800Nuniform distributed load w= 100 N/mlength of cantilever beam L=2m

Q: According to what is given in the cross-sectional picture at Km 1; a) Determine the condition of…

A: Diagram:-

Q: The rod has a circular cross section. If it is made of an elastic perfectly plastic material,…

A: The shape factor of the round bar is independent of the radius of the cross-section.

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.