6.5 The rolled-steel beam shown has been reinforced by attaching to it two 12 x 175-mm plates, using 18-mm-diameter bolts spaced longi- tudinally every 125 mm. Knowing that the average allowable shear- ing stress in the bolts is 85 MPa, determine the largest permissible vertical shearing force. Fig. P6.5 W250 x 44.8 6.6 Solve Prob. 6.5, assuming that the reinforcing plates are only 9 mm thick.

6.5 The rolled-steel beam shown has been reinforced by attaching to it two 12 x 175-mm plates, using 18-mm-diameter bolts spaced longi- tudinally every 125 mm. Knowing that the average allowable shear- ing stress in the bolts is 85 MPa, determine the largest permissible vertical shearing force. Fig. P6.5 W250 x 44.8 6.6 Solve Prob. 6.5, assuming that the reinforcing plates are only 9 mm thick.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

determine the maximum out P that can apply to the joint shown in fig. P2.30. bolt shear stress must not exceed 10,000lb / in ^ 2. Bolt diameter is 5 / 8in.
es Required information Problem 01.061- A two link assembly with point loads Two horizontal 13-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in diameter pin is used at each connection. 0.5 in. 18 in.. 60 45% 0.5 in. 18 in Problem 01.061.a - Shearing stress at a pinned joint within a two link assembly Determine the average shearing stress in the pin at C The average shearing stress in the pin at Cis 38.066 ksi
Q.2/ Analyze the truss shown below by consistent deformation method, EA=1*105 kN 20kN 40kN 2m 20KN F 4@3m=12 201 2m 2m M5Mouk
6-1 For the rectangular beam shown in Fig. P6-1, (c) Sketch, on a drawing of the beam, the inclined cracks that would develop at A, B, and C. (a) Draw a shear-force diagram. (b) Assuming the beam is uncracked, show the direc- tion of the principal tensile stresses at middepth at points A, B, and C. 10 kips 10 kips 1 kip/ft A B 6 ft to 7.5 ft 7.5 ft Fig. P6-1
help find the stress at segment BC, please
4. Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using allowable stresses of T = 80 MPa and o= 120 MPa, how many 20 - mm diameter rivets are required to fasten member BC to the gusset plate? Member BE? What is the largest average tensile or compressive stress in BC and BE? 14 mm plate 6 m C G. 4 m 75 x 75 x 13 mm 96 kN 200 kN 96 kN N 75 x 75 x 6 mm Figure P-130 and P-131 PBC 5. The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.5-in.-diameter pin at A, and the 0.375-in.-diameter cable BC. The working stresses are 25 ksi for the cable, 18 ksi for the boom, and 13.6 ksi for shear in the pin. Neglecting the weight of the boom, determine the largest safe load P that can be applied as shown. 70 4 in. 3.5 in. 30 0.5-in. dia. A. Detail at A
S9. Knowing that the allowable normal stress for the steel used is 160 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m |D B -2.4 m- '0.8 m 0.8 m Figure 9.0 S10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 100 MPa. Consider the beam of S9 above.
Determine the maximum force P that can be applied to the joint shown in Fig. P2.21. The shear stress in the bolts must not exceed 10,000lb / in ^ 2. the diameter of the bolts is 3/4
Figure 2 represents a plane truss ABCDEF that carries two vertical point loads at joints A and C as shown. B 5 m 5 m 5 m 5 m 5 m 5 m 5 m E 60 kN 40 kN Figure 2: A loaded plane truss 2.1. Making use of the method of sections by considering the section l-l as shown, determine the magnitude of internal forces in members BD, CD and CE. 2.2. Making use of the method of joints, determine the magnitude of internal forces in other remaining members of the truss. Calculate the magnitude and show the directions of the support reactions at joints E and F. 2.3. Re-drawing the entire frame in an appropriate engineering scale, show the nature of internal forces in all members and summarize the calculated magnitude and nature of internal forces in a table. F.
Problem 8.4 Distributed Loads The framing system shown in the figure is subjected to a 7.7 kN point load and triangular distributed load with a maximum magnitude of 9.5 kN/m. You are required to: a) Determine the reaction forces at the Pin D. b) Determine the reaction forces at Pin A. c) Determine the force in the member AC. 7.7 kN B 2.5 m STENDER EERSTE CONNECTION SEAN BUTER PLATING 3.5 m D INNER BOTTOM PLATING TRANSVERSE LONGITUDINAL STRAKE 9.5 kN/m 5 m
1. For the truss shown below, determine the minimum cross-sectional area in bars BD, CD, and CE if the allowable stress of each bar is 5 MPa. 6 kN 3 kN B D 4m 3m A 3m C 3m E 2 m 2 kN 1 kN Your answer
The detail of a truss at the support is glued as shown.SHOW FBD DIAGRAMGiven: shearing stress = 800 kN/m2bearing stress = 6 MN/m2(a) determine “b” based on shearing stress(b) determine “c” based on bearing stress