6.36 Given the network in Fig. P6.36, find (a) the power dissi- pated in the 3-2 resistor and (b) the cnergy stored in the сараcitor. 2H 3H 15 V 6A 2F Figure P6.36

Q: Discuss the different methods of measuring high d.c. voltages.What are the limitations in each…

A: Voltage When charged electrons (current) are forced through a conducting loop by the pressure of an…

Q: Name the following figure

A:

Q: State the main constituent elements of electrical cables, as well as the materials from which they…

A:

Q: It is known that a material has a resistivity value of p = 3 x 10-8 ohm m, has a cross-sectional…

A:

Q: write a Conclusion about Clamper

A: Clampers otherwise called as Voltage Doublers or Level Shifters. Clamping circuits are designed to…

Q: What is GENERATION AND MEASUREMENT OF DC VOLTAGE? Give some introduction about it in 2 page if…

A: According to the question, we have to find the value of  Generation and measurement and generation…

Q: The definition of Current in machine

A: An electrical machine works on the principle of electro-mechanical energy conversion. Any electrical…

Q: use both IEC and NEMA symbols. - Conductors crossing but not connected - Conductors crossing and…

A:

Q: How properties like Electrical, thermal, optical, mechanical are used or function in energy…

A: Electrical energy can be utilized to move charged particles through a wire from a force plant to our…

Q: Hiw/ Find the time function also damping ratio and undamped natural frequency For transfer function…

A: For given transfer function it is asked to find the damping ratio, undamped natural frequency and…

Q: Identify the circuits below and briefly explain each of its behavior. 1. R₁ www D₁ Efia at 2.…

A: The parallel combination of an Inductor and a Capacitor is usually called a tank circuit. This…

Q: The 'skin effecť is a phenomenon experienced when current flows through a metal. Which two of the…

A:

Q: What general conclusion can you draw about the relationship between current and voltage when…

A:

Q: B F E D

A: Given

Q: A carbon brush used to conduct current from the commutator of a DC generator has a length of 4 in.…

A: Find the cross sectional area of carbon brush. If current flow = 400 A Voltage not exceed = 2V…

Q: What is the expression of thermal voltage? Find out the value of the thermal voltage at 300 K.

A:

Q: How would the I-V behaviour be of the following cases. Start by explaining what they are

A: There are various energy levels present in the metals and semiconductors. Electrons are present in…

Q: An electron is ....... than a proton. A. LighterB. Heavier

A: The nucleus of an atom is made up of protons and neutrons, whereas the electrons are present outside…

Q: What does a compatible charge mean? What if the load is not compatible?

A: to explain the compatible charge

Q: What is ohm's law

A: The law was named after German physicist Georg Ohm, who detailed measurements of applied voltage and…

Q: What is the mathematical definition of Kw?

A:

Q: Wire to be used in buildings and homes in the United States is standardized according to the AWG…

A: A: To calculate the expression of diameter of the wire, simple the expression of gauge number using…

Q: Give one source of energy and describe how electrical energy can be generated

A: Most human energy requirements are met by generating electrical energy. Once electrical energy is…

Q: 2. Why would we want to use circuit theory and when can we use it? 3. What are the characteristics…

A: This is the problem from basic laws and parameters of electrostatics. Here it is asked to answer…

Q: Q2/ For the current shown in the figure below, find the charge waveform and then find the value of…

A: The solution is given below

Q: 10. What are the properties of a basic ideal circuit element?

A: Properties of a basic ideal circuit element:

Q: Enumerate 10 important Electrical Materials and briefly describe each.

A: The answer as given below:

Q: Assuming constant temperature, what happens to the resistance of a material when the cross-sectional…

A: Cross sectional area- The cross sectional area is the area of a circle. Thus the cross section of…

Q: 1. Report the experimental välües of a. The current through R1 b. The current through R2 C. The…

A: The solution can be achieved as follows.

Q: Determine the nodes/junctions, Current (I), Loops, Voltage drop on each Resistor (R), and Power (P)…

A:

Q: what is the statement of Lenz law.

A: Lenz's Law states:"The direction of an induced electromotive force (EMF) and the resulting current…

Q: 5c.State hooke’s law and explain it to the changing state of materials.

A:

Q: Find and explain the Ohm conservation expression. b) Stable current circulation is desired for the…

A: Ans(a) Drift current is  a electric current which is caused by a particle pulled by the electric…

Q: Explain Ampere’s law.

A: Application of Ampere's Law: It is used for calculating magnetic induction caused by a long wire…

Q: A-How temperature affects the conductivity of conductive metals and how it affects semiconductors.…

A: with change in the temperature, the value of the resistance of the material changes and thus the…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.