6.10 A horizontal water jet at 70°F impinges on a vertical- perpendicular plate. The discharge is 2 cfs. If the external force required to hold the plate in place is 200 lbf, what is the velocity of the water? PROBLEMS 6.10, 6.11

Q: A cylindrical specimen of a cold-worked brass has a ductility (%EL) of 22%. If its cold-worked…

A: CW = [(A1 - A2)/A1] * 100% ........equation 1   Where CW = cold worked percentage gain for( 22% EL)…

Q: The Block shoun in Figure #5 Weighs 20000 16S. Find tere value of x TFF Figure #5

A: To determine the value of x.   Given, Weight of the block (W) = 30000 lbs Cross-section of the…

Q: Derive and show the relationship or transformation of Ws = Ys Vs →→ to Ws=ite v Gm your

A:

Q: Given Y = 9.79 kN/m^3 Find: P @ bottom of tank (kpa) Force (tensile) on each bolt (kN) Stress on…

A:

Q: Relative roughness, eD 当 64/Re at now Darey friction factor, FIGURE Q3(d) 100000 H1000000=gP…

A:

Q: COMPLETE THE STATEMENTS BELOW. TYPE YOUR ANSWERS IN THE BOX. Refer to the figure shown. Given a…

A: Given Data Determine  1. In collapse-2, Y1 = ? θ 2. In collapse-2, Y2 = ? θ  3. In collapse-2, Y2…

Q: y 53 mm 85 mm 25 mm 57° 25 mm - b 65 mm

A:

Q: Weight of container, Wc 6.35 kg Weight of container with water, Wc+w 20.378| kg Table 3. Unit Weight…

A:

Q: Replace the loading by an equivalent resultant force. Suppose that w =2 kN/m and wy = 4.5 kN/m…

A:

Q: Give the value of Plastic modulus for ISHB 250 @ 54.7 kg/m weight.

A: Brief concept introduction- ISHB 250 is the short name for the Indian Standard Heavy Weight Section…

Q: PROBLEM 1: A barge is pulled by two tugboats. If the resultant of the forces exerted by the tugboats…

A:

Q: Size (mm) 0.25 0.149 0.075 0.052 0.02 0.01 0.004 0.001 pan Weight retained (g) 18.96 33.18 45.03…

A: A sieve analysis (or gradation test) is a practice or procedure used in civil engineering and…

Q: True or false? Ao, > q (q is the pressure from building) True or false? Ae increases H increases…

A:

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine…

A: Please find the answer in the below attachments

Q: Cords AB, AC, and AD in (Eigure 1) can sustain a maximum tension of 65 N before they fail Figure 1…

A:

Q: SE80 N E=200 GPG I=(0040" mn 8M greral morent equetim slepe of deflectinm equatin - deplectim…

A: NOTE - : Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: 4m B 3m 28 KN/m 6m D 4m

A:

Q: what is design strength. The material of the steel is SM275 and the size is 22mm. The sectional area…

A: Tensile Strength : Tensile means "competent of being drawn out or stretched." Steel's tensile…

Q: Problem 4.100 Replace the force system acting on the beam by an equivalent force and couple moment…

A:

Q: Betermine the volume V and total surface area A of the solid generated by revolving the area shown…

A:

Q: A 4.020-gram bullet is projected horizontally to a block of timber that rest on a horizontal floor.…

A: Given mass of the bullet  m=4.02 gmbullet is projected horizontallylet the initial speed of the…

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A: Given data:θ = 35°  P = 196 N μs = 0.20 μk = 0.15F = 800 NThe mass of the block is not given, so we…

Q: Part A Determine the magnitude of the resultant force. Express your answer to three significant…

A: Part ARx=∑Fx     =-2.5×45 + 1.5 cos60°     =-1.25 kNRx=1.25 kN ←Ry=∑Fy     =-2.5×35 - 1.5 sin60° - 3…

Q: (A) Give reasons: Very early strength of concrete increases if temperature during placing and…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Q: sketch them please!   please read all of the steps and see the image for the diagram of the…

A: So first i will help you understand how to determine if it is determinate, indeterminate, stable and…

Q: m 1 Replace the loading system by an equivalent resultant Force and couple moment acting at point A.…

A: Given F1=130lb F2=60lb F3=180lb

Q: Given the following data: B. Compact Unit Weight Determination Fine Aggregate a. Weight of measure,…

A: Total weight of sample = (Weight of measure + sample) - (weight of measure) Total weight of sample =…

Q: A beam of square cross-section is bent in the plane of its diagonal. A cut is made at top and bottom…

A: A beam of square cross-section is bent in the plane of its diagonal.A cut is made at the top and…

Q: 3m 31 3m For the frame provided below, consider the following properties * Members along Level a…

A: Please post determination of axial force diagrams and shear force diagrams as a separate question by…

Q: Calculate the following: e. D75, a. D10 b. D25 c. D30, f. Cu, g. Cc, h. So d. D60'

A: Sieve   Mass  % Cumulative % Cumulative % No Sieve size Retained mass Retained Retained   #4…

Q: Modulus of elasticity and Poisson's ratio of a material are 2-1 x 105 N/mm? and 0-25 12.…

A:

Q: Discuss the following terms briefly: I. Water bound and aggregate base, 2. Cross slope and side…

A: Answer Water Bound and aggregate base 1-water bound is known as the water-bound macadam. The…

Q: Which method designs a bylaw based on a coefficient?

A: Coefficient are use to minimize or maximize the value to include adequate safety in the design.

Q: The 580-kg uniform beam is sub three external loads shown. Con reactions at the support point O is…

A:

Q: Problem 3.46 Each spring has an unstretched length of 2 m and a stiffness of k = 330 N/m.(Figure 1)…

A:

Q: THE MEASURE USED HAS AN OUTER DIAMETER OF 15cm AND AN INSIDE HEIGHT OF 16cm. ALSO, THE MEASURE HAS A…

A: Given: Outer Diameter = 15cm Wall thickness = 2.5mm Inside Height = 16cm Bottom thickness = 5mm…

Q: Discuss the advantages and disadvantages of different methods in determining particle size?

A: Air Permeability Fisher Method:-  A fisher sub seive sizer works on the air permeability fisher…