6.1) A boiler produces 25 kg/s of steam at 3 MPa and 600 °C, cools the condenser with seawater so that the outlet is at 45 °C, then a reheating at 500 kPa up to 400°C is carried out, then a low-pressure expansion is carried out in the turbine. Determine: A) The net power output B) The total heat transfer in the boiler

6.1) A boiler produces 25 kg/s of steam at 3 MPa and 600 °C, cools the condenser with seawater so that the outlet is at 45 °C, then a reheating at 500 kPa up to 400°C is carried out, then a low-pressure expansion is carried out in the turbine. Determine: A) The net power output B) The total heat transfer in the boiler

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2Air enters an insulated turbine at 50°C, and exits the turbine at - 30°C, 100 kPa.The isentropic turbine efficiency is 70% and T1=50C V=20L/s the inlet volumetric flow rate is 20 L/s. What is the turbine Air turbine inlet pressure and the turbine power output? T2=-30C.P2=100kpa
There is a steam power cycle that uses water as the working fluid, where the condenser pressure is 20 kPa. The pressure in the boiler is 4 MPa. The steam that comes out of the boiler is saturated steam and the quality at the outlet of the turbine is x4 = 0.65. The water enters the pump as a saturated liquid and exits at a temperature of 48 ° C (T2). Determine a) Work at the pump b) Heat transfer in theboiler c) work on the turbine d) The heat in the condenser e) The thermal efficiency of the cycle
3- Air enters the compressor of a gas turbine at 120 kPa, 310 K. The air compressed to 1100 kPa, the turbine inlet temperature is 1460 K and the expansion occurs in two stages, with reheat to 1420 K between the stages at a pressure of 300 kPa. The compressor efficiency is 85 %. The net power developed is 2.2 MW. sketch T -S diagram then Determine: The thermal efficiency of the cycle. Qin Qin The back work ratio. Combustor Reheat combustor Turbine Turbine stage 1 stage 2 cycle Compressor
Please help me with this question fast and I will leave a like thanks :))
Given • isentoopie efficiency of the turbine isentropie · To find 86 and 91% If Dolynesi toraction Shoud not 86%. " of Pump = 91% Boiler = at State 6 be more than 1%. 1% Thermal efficiency of Puant 2 MPa (Pump 13 MPa, 600 C Turbine Condenser
A rankine cycle with water superheats to 500.546oC at 3.1546 Mpa in the boiler and the condenser operates at 100.546oC. All the components are ideal except the turbine which has an exit state measured to be saturated vapor at 100.546oC. Find the cycle efficiency with a) an ideal turbine and b) the actual turbine. Draw the schematic diagram and T-s diagram.
4
PROBLEM 2.0 The working substance for a Carnot cycle is 9 Ib of air. The volume at the beginning of isothermal expansion is 10 cu ft and the pressure is 300 psia. The ratio of expansion during the addition of heat is 2 and the temperature of the cold body is 90°F. Find The heat added BTU. The heat rejected in BTU. The mean effective pressure in psi The ratio of expansion during the isentropic process The overall ratio of compression.
Steam enters the turbine at 10 MN/m2and 450oC. The steam expanded in the turbine down to the condenser pressure of 20 kN/m2. The condensate leaving the condenser is pumped to the boiler pressure directly. The turbine has an isentropic efficiency of 89%, and the mass of steam generated in the boiler is 5 kg/s. Find: Cycle thermal efficiency. Plant power output.Neglect the pump work and draw the cycle on a T – s diagram. Hint: 1 MN/m2= 10 bar
Consider the re-heat regenerative cycle as shown in the figure below:Suppose that the boiler operates at a constant pressure of 15MPa. The High Pressure turbine expands steam until 4MPa. The Low-pressure turbine then achieves expansion to 700 kPa and 20 kPa. Determine the specific work of Pump II in kJ/kg. a.3.66 b.0.69 c.15.23 d.15.84