6.0 SUPPORT REACTIONS Example 8: Determine the reactions at A and E for the truss supporting a floor deck shown below. The deck is simply supported on floor beams which, in turn are connected to the joints of the truss. Thus, uniformly distributed loading on the deck is transmitted by the floor beams as concentrated loads to the top joints of the truss. Floor beam Deck 15 kN/m B ID 2 m

6.0 SUPPORT REACTIONS Example 8: Determine the reactions at A and E for the truss supporting a floor deck shown below. The deck is simply supported on floor beams which, in turn are connected to the joints of the truss. Thus, uniformly distributed loading on the deck is transmitted by the floor beams as concentrated loads to the top joints of the truss. Floor beam Deck 15 kN/m B ID 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the force in member DF.

A: From the given figures, it is required to find force in member DF and EG.

Q: floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa…

A: Given-

Q: Determine the reactions at the supports for the beam shown. Show handwritten free body diagram and…

A: The answer is attached in the form of an image as follows:

Q: Determine the reactions at the supports for the beam shown. Show free body diagram and solutions.

Q: The resultant force of the forces FA and Fa in the steel cables is FR N. Calculate: COLLAPSE IMAGES…

Q: A 5 simply supported beam ab supports a trapezoidally distributed poad. The intensity of the load…

A: Introduction : When a support keeps a body from moving in a certain direction, a force is applied to…

Q: Problem 2: Determine the reactions of the structure shown below. 15 kips B w = 4 kips/ft /C hinge…

A: A compuond frame with both ends pinned and a hinge at point C.To find: Support reactions at point A…

Q: Determine the reactions at A and B for the steel bar and loading shown, assuming a close fit at both…

A: Given data:- Conditions given-Remove restriction at A and solve for the reactions Below bar figure…

Q: What is the first step of analysis in MCD? a. Determine the degree of indeterminacy of the given…

A: The force method of analysis, also known as the method of consistent deformation, uses equilibrium…

Q: d. Find the reactions at the supports. Major topic - Stiffness Method of AN Analysing Structures 400…

A: solution: Analyse the pin joint truss by stiffness matrix method ∆=K-1×P Element Coordinate forces…

Q: 10 kN 15 kN/m 15 kN/m 2.0 4.0 4.0

Q: 6.5 KAI 5KN 4.1 KN OkN 3.9 kN 7.9m 子.2 m 1 1. to t6.9 m1 1 ,4.8m: 6.9 m 8 m 1.

Q: 4 kN/m 2 kN/m В A 3 m 3 m

Q: ANALYSIS OF STATICALLY DETERMINATE STRUCTURES INTERNAL LOADINGS Prob] Determine the internal forces…

A: Determine the internal forces acting at midspan of beam CD of the frame shown..

Q: For the beam below 2m 3100 N 800 N 200 N 400 N 800 N/m 3 m The absolute value of the shear force at…

Q: Problem 3. The truss is shown below. a. Sketch the influence lines for the support reaction at E,…

Q: PROBLEM 2 Determine the reactions at the supports at A, B and D. Assume that A is roller and B is a…

A: A frame is hinged at B and the roller is supported at A, with loading as shown. To determine the…

Q: For the given truss shown, determine the reaction in kN of the hinge support D

A: Question is based on the truss supported roller and hinge support . Magnitude of loading and length…

Q: Solve the following problem and show your complete solutions. Explain your answer for better…

Q: For the given truss shown, determine the reaction in kN of the hinge support D. ... B 10 KN 4 m A 3…

Q: Approximately, what is the maximum bending moment in this structure under the load case shown? poco…

Q: Q.For the truss loaded as shown in Figure 5, make calculations for the reactions at the support and…

A: determine the angleθin ∆ACD,tanθ=22=1θ=45°therefore,using equilibrium…

Q: Please calculate the support reactions and the connection forces at joint C for the structural…

A: Determine the support reaction of the frame and forces at the joint-C.

Q: Determine the reactions at the supports for the beam shown. Show handwritten free body diagram and…

Q: 4. The truss structure pictured below is supported by a pin at A and a roller at B. Determine the…

A: Free body diagram of truss structure :

Q: b) The structure below could be solved using statically indeterminate method. As a civil engineering…

A: Statically Determinate:The given section can be analyzed completely using the equilibrium…

Q: 3. Determine the reactions and draw the shear and bending moment diagrams for the beam shown using…

A: To: determine the support reactions draw the shear and moment diagrams In the method of…

Q: SHOW THE FBD. SOLVE THE SUPPORT REACTIONS OF THE FOLLOWING STRUCTURE: BEAMS 4 kN/m 2 kN/m A В 3 m 3…

Q: SOLVE THE SUPPORT REACTIONS OF THE FOLLOWING STRUCTURE

A: Consider the figure,

Q: 2 kN/m 10 KN Z 4 kN/m 20 KN Z 20 m Figure P1.3 15 m 15 m

A: A frame is given we need to find out the reactions at supports.

Q: calculate the resultant distributed loading and the supports reactions for the following beam 1/2 w…

Q: Find the reaction at support A (RA) B. Find the reaction at support C (Rc) C. Draw the shear…

Q: . What is the vertical reaction component at the hinge? See figure 4 b. Find the total number of…

A: Here a truss is given with a hinge at end A and a roller at end L. Hence we need to find out the…

Q: Q. Determine the support reactions of the shown beam Fixed 2 kN 3 kN. m A 2 m 1 m 1.5 m 1.5 m

Q: What is the maximum tensile force on member BG? What is the maximum compressive force on member BG?

Q: Situation C. The plane truss is loaded as shown. Assume A = 1,300 mm2 and E = 200 GPa 10 kN 40 kN 1…

A: Given:- A=1300 mm2E=200 GPa To find:- Reaction at roller support Force in member ac

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

6.0 SUPPORT REACTIONS
Example 8:
Determine the reactions at A and E for the truss supporting a floor deck shown
below. The deck is simply supported on floor beams which, in turn are connected to
the joints of the truss. Thus, uniformly distributed loading on the deck is transmitted
by the floor beams as concentrated loads to the top joints of the truss.
Floor beam
Deck
15 kN/m
TD
ET
2 m
F
G
-2 m-2 m-2 m-2 m-2 m--2 m-2 m-2 m-|
76
DELL

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 : Diagram

Step 2: Explanation

Step 3 : Reactions

Step 4: Alternate

Step 5: ANSWER

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the reactions at the supports for the beam shown. Show free body diagram and solutions.
F M M A В a b a Calculate the reaction forces of the structure, with the sign convention drawn! What is the magnitude of the maximal shear force (IVIma) the sructure is subjected to? Give the maximal (M) and minimal (M - most dangerous negative) bending moments the structure is subjected to! See the sign convetion drawn! max min q = 13.00 [kN/m] F = 55.00 [kN] a = 1.40 [m] b = 10.00 [m] %3D Results: v A = [kN] [kN] [kN] MI. [kN] 'max M [kNm] max v M [kNm] %3D min >
I need the answer as soon as possible
SUPERPOSITION METHOD
The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa and a uniformly distributed live load of 1.9 kPa over its surface area. Determine the service (ASD) reaction (kN) of beam BG that will be transferred to the girder at G. Girder Floor beam Column A Į B FH -IK G L H M 4 at 7.5 m = 30 m D N E 2 at 12 m = 24 m
Please asnwer step by step pleaseee
Q1: A torque T= 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa, Determine: (a) maximum shearing stress in the in the steel core (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A.
Determine the reactions at the supports for the beam shown. Show free body diagram and solutions.
SHOW THE FBD. SOLVE THE SUPPORT REACTIONS OF THE FOLLOWING STRUCTURE:
THESE ARE THE ANSWERS GIVE THE SOLUTION AND FREE BODY DIAGRAM FOR THIS PROBLEM. Answers: Ax = 0 Ay = 2.49 N Ca= 0.603 Nm