6. Suppose the length L of the uniform bar is 3.0 m and its weight is 210 N. The block's weight is 340 N and is located at distance x -0.75 m from the wall, and the angle e = 25°. What are the (a) horizontal and (b) vertical components of the force on the bar from the hinge at A? com

6. Suppose the length L of the uniform bar is 3.0 m and its weight is 210 N. The block's weight is 340 N and is located at distance x -0.75 m from the wall, and the angle e = 25°. What are the (a) horizontal and (b) vertical components of the force on the bar from the hinge at A? com

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 24P

See similar textbooks

Related questions

Q: 1. A uniform log with a mass of 100 kg, a length of 4.0 m, and a radius of 12 cm is held in an…

Q: 02 Pin

Q: before starting this problem. A uniform plank of length 5.0 m and weight 225 N rests horizontally on…

A: Given:- length(L)=5m Plank hanging (d)=1.1 m Weight (W) = 225 N At distance person weight (w)=mg=375…

Q: 12) In the figure, a 10.0-m long bar is attached by a frictionless hinge to a wall and held…

A: Length of the bar is L = 10 m Angle of the rope with the bar is 53 degrees Weight of the bar is W =…

Q: In the figure below, suppose the length L of the uniform bar is 3.10 m and its weight is 210 N.…

Q: The figure shows three boards clamped together. The center board weighs 93.5 N, and the coefficient…

A: The figure shows the force acting on the three boards clamped together.

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500-lb load.…

Q: 9. A uniform ladder of mass (m) and length (L) leans against a frictionless wall, see figure. If the…

A: The net torque is zero. Therefore,

Q: One end of a uniform 3.80-m-long rod of weight Fg is supported by a cable at an angle of ? = 37°…

Q: 12.Based on the figure, assume the somewhat artificial condition that the strut is weightless and…

A: Given, Weight, W = 10 N Tension, T Normal force, N Angle made by T with the horizontal is, 37° the…

Q: 4. A uniform 312 kg boom is 10.0 m long is held up by cable attached 6.00 m from the wall at an…

Q: A uniform 312 kg boom is 10.0 m long is held up by cable attached 6.00 m from the wall at an angle…

A: Given: The mass of the boom is m=312 kg, The distance of cable from wall is PQ=6 m, The length of…

Q: Determine the minimum distance x from point A at which an additional weight w (the same as the…

Q: In the figure, a uniform rod of mass m is hinged to a building at its lower end, while its upper end…

Q: In the figure, suppose the length L of the uniform bar is 3.00 m and its weight is 200 N. Also, let…

Q: 10) One end of a uniform beam is hinged to a wall and the other end is supported by a tension wire…

A: The shown beam is in equilibrium. Need to calculate the tension in the wire. Also, it is required to…

Q: F FB A CG B A mg = Assume FA is down and the 20 kg board is 5 meters long. The board is in static…

A: Dear student When objects are in static equilibrium, the net force as well as net torque on it is…

Q: Q12) The figure shows a uniform, horizontal beam (length - 10 m, mass - 25 kg) that is pivoted to…

A: Draw the free-body diagram of the beam.

Q: A sandwich board advertising sign is constructed as shown in Figure 5.39. Its mass is 7.80 kg.…

Q: 3. A person with a mass of 55kg stands 2.0 m away from the wall on a 6.0 m beam as shown in the…

A: mass of person , M=55 Kg mass of beam, m= 40 Kg Point O is b/w beam & wall. Mass of beam will…

Q: A sandwich board advertising sign is constructed as shown in figure 5.39. It's mass is 6.90 KG. (a)…

A: Given;- A figure is given as A sandwich board advertising sign is constructed as shown in the…

Q: 53 5 m A uniform 80N beam that is 5 m long is attached to a wall by a cable as shown in the figure.…

Q: 1) A tapered log 3.0 m long weighs 210 N and has its center of gravity 1.0 m from the thick end. It…

Q: ah object to remain static, what two conditions must be true? A) Sum of integers = 0 %3D B) All…

A: Let an object be at static state, no linear or angular motion. It will not get any linear motion if…

Q: It's exciting watching the construction and renovation happening in Uptown Columbus! On one…

Q: L d- ms A horizontal L=1.3 m long mb=15 kg uniform bar is hinged on the left end and pulled at the…

Q: Please help me with all the parts in this question, there are multiple parts, double and triple…

Q: 1. A 140 kg uniform beam is attached to a vertical wall at one end and is supported by a cable at…

A: Given: Weight of beam = 140 kg. Let the length of the beam = L. Angle (θ) = 39.0 Let, the vertical…

Q: A uniform beam 3.7 mm long and weighing 3000 NN carries a 3000 NN weight 1.50 mm from the far end,…

Q: A ladder weighing 180 N is set against the wall and does not slip. There is friction between the…

A: No friction between ladder And floor . Centre of mass is at Midway of ladder . Weight w = mg = 180 N…

Q: In the figure, suppose the length L of the uniform bar is 3.1 m and its weight is 240 N. Also, let…

A: We will calculate the torques exerted on the system around the hinge. a) Calculate the torque…

Q: أة *

Q: A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal…

Q: 1.Two people are carrying a uniform wooden ladder that is 3.0 m long and weighs 100 N. if a man…

Q: 4. A uniform rod 2 m long and weighing 65 N is pivoted to the wall as shown. A weight of 25 N is…

Q: A uniform 22 kg beam, 3.0 m long, is attached to a wall on the left by a hinge, and is supported by…

Q: What force is exerted by each side on the hinge?

Q: 10. An object weighing 225 N is supported by a uniform 120 N horizontal beam as shown in the figure.…

Q: A 500.-N uniform rectangular sign 4.00 mwide and 3.00 m high is suspended from ahorizontal,…

A: Given data:Weight of the rectangular sign = 500 NWeight of the rod = 100 NLength of the rod, = 6.00…

Q: 8. A uniform beam, length = 12 m, wt = 800 N, is hinged at the wall and makes an angle of 30° to the…

Q: 2. A uniform ladder rests against a smooth wall so that it makes an angle of 60° with the ground.…

A: Assume the situation as below, Here d is the distance the child can go, f is the friction force, NA…

Q: A sandwich board advertising sign is constructed as shown in Figure 5.39. Its mass is 9.40 kg. ( see…

Q: 6. A cable supports a uniform boom, which is pivoted at point P. ogble boom P 60.0° If the cable is…

Q: My book has the answers as a) 10N b) 196N But I can't figure out the proper way to work it out. I…

Q: A uniform drawbridge must be held at a 36.5 angle above the horizontal to allow ships to pass…

Concept explainers

Center of Gravity of a system

The centre of gravity is a property that is based on the geometry of a rigid body or any particle. It is described as an equilibrium point or a hypothetical location where the total weight of the body is concentrated.

Question

Suppose the length L of the uniform bar is 3.0 m and its weight is 210 N. The
block's weight is 340 N and is located at distance x = 0.75 m from the wall, and the angle =
25°. What are the (a) horizontal and (b) vertical components of the force on the bar from the
hinge at A?
com
4.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A rectangular plate is supported by three cables as shown. Knowing that the tension in cable AB is 440 N, determine the components of the force exerted on the plate at B. y 130 480 B 320 450 Dimensions in mm The x component of the force is The y component of the force is The z component of the force is 250 D 360 360 x N. N. N.
Three pairs of flexible cables, spaced at 120° inter- vals, are used to stabilize a 1000-ft television tower. The tower and one pair of cables is shown in Fig. weight of the cables is 3.0 lb/ft. The horizontal component of the force exerted by each cable is 6000 lb. At anchor A, the angle between cable AC and the horizontal must be 40°. Determine The The horizontal distance d from the tower to anchor A. 400 ft B 400 ft KKKKKKKKKKI
P= SN kN I. For the force in the figure, determine the rectangular components along u and v axes if a = 20° y 60- a a P. 2. For the force Pin the figure, determine the components P, and Pa, if the former is directed 80° from the horizontal axis( a-axis) and the latter 20° to the same reference axis. Force P = FN kN is acting at a given angle of 60* from the x axis. P2 а- ахis P = FN kN P= MN kN 3. For the force system shown in the figure determine the horizontal and vertical components of each force. 3 P= SN kN %3D Page 1 of 2
A uniform horizontal beam with a length of 8 m and a weight of 200 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of 53° with the beam. If a 600-N person stands 2 m from the wall. What is the ?tension in the cable 53.0% 8.00 m .A None .B N 410
35.0° Dinysics Demos SuDDly Co. The pole is held horizontally by a massless wire under 305 N of tension, connected at a 35° angle. A 8 kg sign hangs from the end of the 4 meter pole. The pole has mass 4 kg. How far away is the wire is attached from the wall? Answer in meters to 3 sig figs.
16. ao The drawing shows a rectangular piece of wood. The forces applied to corners B and D have the same magnitude of 12 N and are directed parallel to the long and short sides of the rectangle. The long side of the rectangle is twice as long as the short side. An axis of ro- tation is shown perpendicular to the plane of the rectangle at its center. A third force (not shown in the drawing) is applied to cor- ner A, directed along the short side of the rectangle (either toward B or away from B), such that the piece of wood is at equilib- rium. Find the magnitude and direction of the force applied to corner A. A D Axis Problem 16
The forces are in static equilibrium. The 140 lb force is directed along the x-axis and the 300 lb force is directed along the negative z- axis. Determine the magnitude of the unknown force, R. Z X R Ox лог 140lb A (-50, 80, 160) lb By 300 lb у
A cable stretched between the fixed supports A and B is under a tension T of 1.6 kN. Express the tension as a vector using the unit vectors i and j, first, as a force TA acting on A and second, as a force Tg acting on B. 460 mm А y 340 mm Answers: TA = ( b) kN i+ Tg = ( b) kN
Q1 Q1\ ABD consists Isosceles triangle. The AB and AD help support pole AC. Known that the tension in AB is double AD tension and the distance between A and C is 0.7 of BD. Determine the magnitude of these tensions if the value of resultant forces is 120 Ib. B.
A 1204-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end A 1515-N crate hangs from the far end of the beam. Find the magnitude of the tension in the wire. The angle theta (9) is 29 degrees and the angle phi () is 53 degrees. The length of the beamis L Вeam ROUND OFF FINAL ANSWER TO THE NEAREST WHOLE NUMBER. INPUT THE SYMBOL OF THE UNIT. NO SPACE BETWEEN THE NUMBER AND THE UNIT.
From the step ladder shown in the figure, sides AC and CE are each 2.44 m long and hinged at point C. Bar BD is a tie-rod 0.762 m long, halfway up. A man weighing 845 N climbs 1.8 m along the ladder. Assuming the floor is frictionless and neglecting the mass of the ladder, find the tension (in N) in the tie-rod.
The two structural members, one of which is in tension and the other in compression, exert the indicated forces on joint O. Determine the magnitude of the resultant R of the two forces and the angle which R makes with the positive x-axis. The angle is measured counterclockwise from the positive x-axis. 4.2 KN 1.6 kN Answers: R= i 0= i 28° // 20/000 HOT N lad wwwww 63° KN O