6. A piston-cylinder device initially contains 0.07 m³ of nitrogen gas at 130kPaa and 180°C. The nitrogen is now expanded to a pressure of 80kPaa polytropically with a polytropic exponent whose value is equal to the specific heat ratio. Determine the final temperature (C) and the boundary work (k) done during this process. Page | 93

6. A piston-cylinder device initially contains 0.07 m³ of nitrogen gas at 130kPaa and 180°C. The nitrogen is now expanded to a pressure of 80kPaa polytropically with a polytropic exponent whose value is equal to the specific heat ratio. Determine the final temperature (C) and the boundary work (k) done during this process. Page | 93

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SHOW COMPLETE SOLUTION PLS A piston-cylinder device initially contains 65-L of liquid water at 40C and 190 kPa. Heat is transferred to water at constant pressure until the entire liquid is vaporized. What is the mass of the water?
Mr Luda wants to understand further about a newly created gas. The gas is initiallyat a pressure of 90 kPa, volume of 1.258 m3 and temperature of 10°C (State 1).The gas undergoes a 3-step process in which it is first compressed isothermally toa pressure of 400 kPa and volume of 0.283 m3 (State 2), then expanded at constantpressure back to its original volume (State 3). Finally, the gas is returned to itsoriginal State 1 by cooling at constant volume.a) Sketch the cycle of this system on a P – V diagram.b) Calculate the work done (in kJ) for each process step.c) Determine the total work done for the three-process cycle.d) State whether the work done is on or by the system.
1. A frictionless piston-cylinder device with cross-section area of 0.01 m² contains 0.5 m3 gaseous ammonia initially at 200 kPa and 135 °C. Now the gas is isothermally compressed until the pressure increases to 800 psig. The surrounding pressure is 100 kPa and the gravitational force is 9.8 m/s? a. What is the mass of the gas in kg b. What is the mass of the piston in kg c. Calculate the volume in m³ of the compressed gas
A piston- cylınder device contains axygen, and the pAston Is free to móve. The initial temperature and pressure of the oxygen are, Oxygen is cooled untu" the specific volume becomes 0.15 m/kg while it behaves as an ideal gas, and if the total work done on the System is 300 kJ, Calculate the mass of the oxygen in kg using 5 signifigant fAgures. respectvely , 200°C and 0.le MPa. If the
A mass of 0.1 kg of helium fills a 0.2 m³ rigid vessel at 350 kPa. The vessel is heated until the pressure is 710 kPa. Calculate the temperature change of helium (in K) as a result of this heating. The gas constant of helium is R= 2.0769 kPa-m3/kg-K. Helium 0.1 kg 0.2 m 350 kPa The temperature change is K.
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
An ideal gas expands from 11.5 cu.ft to 17.5 cu.ft at 85 deg.F and 15.5 psia. During the isobaric process, what will be the temperature of the gas?
A reservoir contains 2.83 cubic meters of CO at 6895 kPa and 23.6 degrees CELSIUS. A cylindrical tank with h = 1.5D is filled from the reservoir to a pressure of 3497 kPa and a temperature of 12.4 degrees C, while the pressure and temperature in the reservoir decreases to 6205 kPa and 18.3 degrees C respectively. (ANSWER MUST BE EXACT TO CHOICES) a) the total mass of CO transferred to the tank in kg CHOICES 19.62 18.54 203 b) the total volume of the tank in cubic meter CHOICES 0.476 0.495 0.449 c) the diameter of the tank in mm CHOICES 671.8 725 755
Properties of Pure Substancies What is the specific internal energy of water at 50 kPa and 20°C?
ANSWER ALL THREE AND GET A LIKE <3 The density of helium is 0.178 kg/m3 at STP. What is the density in kg/m3 at 25°C and 98 kPa? A steel tank initially contains oxygen gas at 450 kPag and 20°C. After 2.5 kg of oxygen had been used, the pressure and temperature of the gas in the tank was found to be 180 kPag and 20°C, respectively. What was the initial mass of oxygen in the tank in kg? A 1500-L tank contains nitrogen at a pressure of 400 kPag and a temperature of 320K. Later, because of a leak, it was found that the gage pressure has dropped to 320 kPag and the temperature has decreased to 300K, determine the amount of nitrogen that has leaked out in kg.
Given 280 liters of a gas at a 63.5 cm Hg. The gas has a specific heat at constant pressure of 0.847 kJ/kg K and a specific heat at constant volume of 0.659 kJ/kg K. Which of the following most nearly equals the volume of the gas would occupy at a final pressure of 5atm if the process is adiabatic?
A well-insulated tank fitted with an electrical resistor ofnegligible mass holds 1.5 kg of nitrogen (N2 ), initially at 30 °C, 0.2MPa. Over a period of 20 minutes, electricity is provided to theresistor at a constant voltage of 120 V and with a constant currentof 1 ampere. Assuming ideal gas behavior and constant specificheats, determine the nitrogen’s final temperature (in K), and thefinal pressure (in bars).