6. A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular representation of Force Vector P. (b) Determine the moment of P about point O. (c) Determine the moment of P about a line joining points 0 and D. 7.5 in. 7.5 in. 10. E H D 10 in. x 10 in.

6. A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular representation of Force Vector P. (b) Determine the moment of P about point O. (c) Determine the moment of P about a line joining points 0 and D. 7.5 in. 7.5 in. 10. E H D 10 in. x 10 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Determine the reactions and draw the shear and bending moment diagrams for the beams shown in by using the Slope-deﬂection method. There’s a settlement of ½ in. at support B.
Determine the moment of the vertical reaction at point A (A,) rotating about the location (XR) of the equivalent resultant force of the forces acting on the beam shown in Figure 3.1f, i.e. A, X XR. Given /= 1.8, P1 = 30, P2 = 20 and w = 10. (Note: Negative "." for clockwise moment.) [Hint: Find the equivalent resultant force and its location (xR) with respect to point A. Apply correct equation of equilibrium to solve Ay. ] P, kN W kN/m P, kN 21 m 21 m Figure 3.1f
Question 34 of 46 A man exerts a force Fon the handle of the stationary wheelbarrow at A. The weight of the wheelbarrow along with its load of dirt is 215 lb with center of gravity at G. For the configuration shown, what force F must the man apply at A to make the net moment about the tire contact point B equal to zero? Assume a = 43 in., b = 8 in., h = 22 in., 0 = 24°, and = 50°. %3D %3D W B. Answer: F = Ib
L6 3 Q3: A simply supported beam is loaded as shown in figure. A- Draw the shear force diagram and the bending moment for the beam B- Write The position of maximum bending moment * ?on the beam 4KN 6KN ZKN/m 3m 3m 6m 12m
Indicate all necessary FBDS, concepts and formulas needed in the solution. Using the three-moment equations, solve for the Following: | 1.2: moments at supports C and D. E is constant 12KN/m 6KN/m 20KNM 2mp 5m 3m 3m 2m 4m A B D E 2.51 21
Question 40 of 46 An experimental device imparts a force of magnitude F = 67 lb to the front edge of the rim at A to simulate the effect of a slam dunk. Compute the moments of the force Fabout point O and about point B. The moments are positive if counterclockwise, negative if clockwise. Finally, locate, from the base at O, a point Con the ground where the force imparts zero moment. The distance d from point O to point Cis positive if Cis to the right of O, and negative if to the left. 12 10
Determine angular velocity of the bar, [rad/s], when it goes through horizontal position? The bar, WA= 100 [lb] and L=3 [ft], shown in figure is initially in the vertical position. The bar is subjected to a couple moment of M=20 [lb-ft] and a force F=50 [lb], which is always perpendicular to the end of bar. Also, the spring is attached to bar at distance L/2 from point A, and has unstretched length of lo=1.2 [ft]. The spring remains in horizontal position throughout the motion due to the roller guide at B. Determine angular velocity of the bar, o [rad/s], when it goes through horizontal position. Spring constant is k=7 [lb/ft]. Distance between point A and vertical guide is d=1.5 [ft]. F g B thing M A d ≈
6. A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular representation of Force Vector P. (b) Determine the moment of P about point O. (c) Determine the moment of P about a line joining points O and D. 7.5 in. 7.5 in. 10 in. E 0 P 30 in. H D B 10 in. x 10 in.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 3.3 ft, b = 3.2 ft, P = 20 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. P A C D E Answer: (a) Vmax= (b) Mmax= a B b lb b lb-ft a