6 kN 9 kNm 4 kN/m E 2 m 0.5 m 0.5 m 2 m

Q: Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing…

A: TRUSS:- is a rigid structure in which all he members are subjected to either axial or  tensile or…

Q: Determine the forces in a. Support reaction at A b. Support reaction at B C. Member in BC d. Member…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: Part A Consider the pipe shown in (Figure 1). The forces F = 400 N F = 500 N, and Fy = 700 N are…

A:

Q: Problem 4: Solve for internal reactions at pin C and D.

A:

Q: DETERMINE THE REACTION AT A AND C. 6 Ib/ft B 6ft 4 ft - Hinge

A:

Q: 4 m A B 2 kN/m

A: THERE IS ONLY TWO UNKNOWN REACTION AT PIN B  IS VERTICAL REACTION Rb AND HORIZONTAL REACTION Hb.…

Q: Determine the reactions of fixed support at A 15 KN 8 kN/m 4 kN/m 60 3m-

A:

Q: Can you give me the free-body diagram?

A: Given data:- A pendulum of mass M1=1 kg  length L = 0.75 m . Mass of Block M2= 2 kg To find :- Free…

Q: +1. 6 in. 1 B 4 in. 5 in. A 200 lb D 10 in.- E Draw the free body diagram and calculate reactions at…

A: The given data  Load at D = 200lb Draw the free body diagram and reaction at support A and E

Q: A post is supported by a ball-and-socket joint at O and cables BC and BD. A triangular distributed…

A: Given data, w = Maximum intensity of UVL = 36 N/m rOA = Length OA = 1.6 m rOB = Length OB = 2.5 m…

Q: Б

A: introduction: here we have to find out reaction

Q: Solve for the reactions at point A. A 9.33 KN B. 10.33 KN C. 11.33 kN 3m B D E -2 m2 m-2 m--2m--2m-2…

A: Given data: The distance between AB, BC, CD, DE, EF and FG is x = 2 m. The force acting on joint B…

Q: C. A beam used as bench for AIT students is supported on its fulcrum at the point, P which is at…

A: (i) The clockwise moment about point P can be written as, M=23 N100 m=2300 N·m Therefore, the…

Q: Determine support reaction

A: Reaction at B: Apply equilibrium condition…

Q: 80 kN 60 kN 10 m 10 m 10 m L: D 20

A:

Q: If the whole truss is in equilibrium then all the joints which are connected to that truss is in…

A: In section method- the unknown forces in the member of truss is to be calculated.this is done by…

Q: IF the maximum tension T that the string can sustain is 2/2W then choose the correct options. (A)…

A: Moment at end point will be zero. Correct options: A B D

Q: Write the three equations of equilibrium?

A: A body is said to be in equilibrium it is not acted upon by any net force in either of the two…

Q: attached

A:

Q: What will be the vertical component of reaction at the rocker B (i.e., ?By) on the beam, if P = 20…

A:

Q: Problems: Determine the reaction -4 in.- 4 in. 40 lb 20 lb 2 in. CO 3 in. 3 in. 30%

A:

Q: The total number of independent equations of equilibrium that we can write for a frame or machine…

A: Six independent equations of equilibrium that we can write for a frame or machine.Option first is…

Q: In analyzing the unknown forces acting on a given pin in a plane truss, obtaining a negative answer…

A: Option 3 is correct  The direction that was chosen for the force was incorrect, and the correct…

Q: Help!!! Answer this correctly!! Please

A: Step 1: Step 2: Step 3: Step 4:

Q: 5 ft 5 ft 12 ft 5 ft reactions in A and D

A:

Q: Examples 5 Determine the reactions at the supports. 600 N/m 900 N/m In your hand

A:

Q: Which of the following corresponds to the vertical reaction at the pin support?

A:

Q: Q4 Find the reactions in supports 50 KN 20 kNm B D A 3 m 1.5 m

A:

Q: What happens when the couple moment is already applied to the body?

A:

Q: Problem 8 Determine the reaction at the roller support A and B and pinned support C. El is constant.…

A: Step 1:Step 2:Step 3:

Q: 5 m B 3 m 3m 80 kN 5 m

A: Draw the free body diagram of the system. Calculate the angle θ.

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.