6 As Manning's roughness increases the flow will ol:(einlo98) Enolles increase. ( ) Pump in branching systems gives the same head for all branches. 7 ( ) 8 For uniform channels, the slope of EGL should equal the slope of the channel. ( ) 9 For a supercritical flow Froude number should be less than unity. ( ) 10 Pumps approach the shut-off head when the flow approaches its minimum value. ( )

6 As Manning's roughness increases the flow will ol:(einlo98) Enolles increase. ( ) Pump in branching systems gives the same head for all branches. 7 ( ) 8 For uniform channels, the slope of EGL should equal the slope of the channel. ( ) 9 For a supercritical flow Froude number should be less than unity. ( ) 10 Pumps approach the shut-off head when the flow approaches its minimum value. ( )

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Pump The oil tanks have a diameter of D = 12m. The initial depth of the oil in tank A is 20m, and in tank B the depth is 1 m. The pump delivers a constant head of 60 m. The connecting pipe has a diameter of b = 0.2m, and the head loss due to friction in the pipe is hyL = 8- Find the time required to fill tank B to 14m depth. (neglect minor losses)
len3
The velocity in this channel is 0.9 m/sec. The Froude number is 6.73 m y=1.5 m 5 m 0.82 .a O 0.25 .b O None of these .c O 0.57.d O
Fluid.mec
Urgent
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.
A pipe has a length of 213 m., and a diameter of 0.46 m. The coefficient of rouaness is C = 171, and the headloss is 17 m. Determine the discharge (L/s) inside the pipe.
For the selection of friction factor, f from the Moody diagram, select the most appropriate answer. O For smooth-walled pipes, we need to know Re only. O All the answers are correct. O For laminar flow, we need to know Re only. O For rough turbulent flow, we need to know Re vs ks/D.
Solve it ASAP
An ideal liquid flowing through a pipe A of cross-section 0.2m² with velocity 10m/s enters a T-junction. One side of the T-junction B has cross-section area 0.1m² and the other side Chascross-section area 0.05m². If the velocity of water in C is 15m/s then in B the velocity is
nat3
Problem 2: A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial at the inlet of the rotor. The pump has the following characteristics: Flow rate Inlet diameter Outlet diameter Head Width at the inlet Width at the outlet Leakage Mechanical loss Blade angle at the outlet The water density Atmospheric pressure |Q=72 L/s DI = 90 mm D2 = 280 mm H= 25m bl -20 mm b2 = 18 mm q =2 L/s Pm = 1.41 kW B2 = 35 p = 998 kg/m³ 101 kPa