6 - A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O →→→T=5 KN•m bross cylinder ro=20mm (outer diameter) Steel core r=15mm G=78 GPa G=39 GP₂"

6 - A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O →→→T=5 KN•m bross cylinder ro=20mm (outer diameter) Steel core r=15mm G=78 GPa G=39 GP₂"

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
1. See figure below and solve for the maximum value of torque the composite shaft can accommodate given a maximum shear stress of 8ksi in bronze and 12 ksi for the steel. Assume bronze has G = 6 × 103 ksi, and for steel, G = 12 × 103 ksi. %3| L C2" 3" Hollow Bronze Steel Core D = 3 in, d = 2 in D = 2 in
4. For the rods shown, determine (a) the compressive force after a temperature rise of 95°C, (b) the corresponding change in length of the aluminum rod. 0.5 m Aluminum A = 2.0x10-3 m2 E 70 GPa a= 23x10-6/Oc + 0.3 m Bronze A = 1.5x10-3 m2 E = 110 GPa d=18x10-6/0c .0 mm
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
1. See figure below and solve for the maximum value of torque the composite shaft can accommodate given a maximum shear stress of 8ksi in bronze and 12 ksi for the steel. Assume bronze has G = 6 x 10° ksi, and for steel, G = 12 x 10% ksi. T L 2" |3" Steel Core D = 2 in Hollow Bronze D = 3 in, d = 2 in
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
PROBLEM 6/6 F = 520 kN Determine the stress in each aluminum and steel bars after 0.2 mm F = 520 kN is applied. Note that a gap of 0.2 mm exist before the external load is Steel 280 mm applied and bars has equal distance with each other. Neglect the weight at the flat form. A = 1100 mm² E = 200 Gpa A = 2500 mm² E = 70 GPa Steel Aluminum
An aluminum tube is fastened between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. For Bronze: Allowable stress = 120 MPa, EB = 83,000 MPa For Aluminum: Allowable stress = 120 Mpa, EA = 70,000 MPa For Steel: Allowable stress = 120 MPa, Es = 200,000 MPa Assume that the assembly is suitably braced to prevent buckling. Maximum overall deformation should not exceed 2mm. a) Give the value of the force acting on the bronze so as not to exceed allowable stresses and deformation. b) Give the value of the force acting on the aluminum so as not to exceed its allowable stresses and deformation. c) Give the value of the force acting on the steel so as not to exceed its allowable stresses and deformation.
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)