5V R -Vin Problem A: If C1 is reduced, will that improve frequency response of the first stage? C1 Vsig' O HI. Problem B: In a certain application R = 10k. If all resistors are changed to 20k, will the frequency response of the first stage be affected, and if so, how. R Problem C: Vsig is a 1Vpp sine wave whose frequency is in the passband of both stages. If the first stage is omitted, and Vsig is fed directly to op amp input Vin, will the signal be amplified linearly? C2 5V R R Vout

5V R -Vin Problem A: If C1 is reduced, will that improve frequency response of the first stage? C1 Vsig' O HI. Problem B: In a certain application R = 10k. If all resistors are changed to 20k, will the frequency response of the first stage be affected, and if so, how. R Problem C: Vsig is a 1Vpp sine wave whose frequency is in the passband of both stages. If the first stage is omitted, and Vsig is fed directly to op amp input Vin, will the signal be amplified linearly? C2 5V R R Vout

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Application: Construct the circuit in figure. Vsı = 10 V, Vy=5 V, R= 330 2, R =1 KQ, R, = 1002 R- 10 KO and R-470 2. %3D R1 R3 RS VS1 R2 R4 VS2 Calculate the umerical valucs of following quantitites VR:, Vsz. VR, Vg4. VRs, IR1, Ir:. Igs. L4, les Show all works. Do the necessary measurements and compare the results. Solution:
An electron is moving in a piece of very lightly doped silicon under an applied fieldsuch that its drift velocity is one-tenth of its thermal velocity. Calculate the averagenumber of collisions it will experience in traversing by drift a region 1 μm long. Whatis the voltage across this region? Temperature= 300°K
IMPLEMENTATION OF XOR AND XNOR GATES USING NAND GATES 1. Material Required: Logic Trainer Connecting Wires Components(IC’s): 40112. Procedure:It is clear from the logic diagram that the NAND gate implementation of XOR gate requiresfive NAND gates. You will need two quad- 2 in NAND gate ICs to perform this experiment.Gets the required number of ICs containing NAND gates and other apparatus from the labattendant. Plug in the ICs in the breadboard of the Logic Trainer. Connect 5Vdc power supplyand ground on pins 14 and 7 respectively. For other pin configuration consult the data sheet (wehave already used NAND gates in the first lab so it should not be a problem). Wire your circuitaccording to the logic diagram for XOR gate as given above. Once you have wired the circuit,check it with your instructor and, if approved, power up your circuit. The outputs should beconnected to the LEDs on the Logic Trainer for monitoring purpose. Apply different inputcombinations at the input and note…
Q3) Construct and design a CMOS NOR gate with two inputs having KN =KP = 500μA/V2, VDD = 3 V, VTN = 1V, VTP= -1 V and load capacitance of 1pF is connected at its output ,determine its switching speed.
Q1/ Consider the depletion load transistor based at Voo - 3 V. Vtn=-2 V, Vtno 0.7 V, (W/L)p-10, such that the maximum power dissipation is 320 μW, when VI-3 V. And Kn=60μA/V, Determine the output voltage.
An ac voltage of peak value 20v is connected in series with a silicon diode and load resistance of 5002. if the forward resistance of diode is 10Q find: i- Peak current through diode. ii- Peak output voltage. iii- What will be these values if the diode is assumed to be ideal (Vdiode =0)?
Q3: Design a full-wave rectifier with Ik2 load. The rectifier operates from A.C supply of 220v (rms) and 50HZ through 20-to-1 step down transformer having a center tapped secondary winding. What is the peak value of the rectified output across the load and the fraction of a cycle does each diode conduct? What is the PIV of the used diodes. The diodes can be modeled to have 0.75v voltage drop for any current.
4 Q: A- For the transistor circuit shown in figure bellow 20 v Determine: 1- Ig , Ic , le and Vce · 2- Sketch the load line (Q-point) of the transistor. 470 2 270 kQ B=125 تمت الاجابة وسارفع الملف لاحقا
a. We discussed in class the "two conditions" that allow current to flow through a MOSFET, and "two conditions" that would not allow current to flow. Write down what these conditions are: b. Consider a n-channel MOSFET and a p-channel MOSFET. How would you connect these two transistors in order to create a basic CMOS Inverter, as discussed in class. c. Now consider a floating gate, containing electrons. Use Gauss' Law to explain whether or not inversion can occur in the channel if a positive gate voltage were to be applied d. Depending on whether or not current flows through the channel, what does this tell you about whether or not you have stored a "0" or a “1”? e. Use principles of Coulomb's Law to explain how you would remove electrons from the floating gate (i.e. to "flash" your flash memory device)
Q4/ In an n-type semiconductor at T=300K, the electron concentration varies linearly from 1017 to 3x 1016 cm-3over a distance of 0.72 cm. calculate the diffusion current density if the electron diffusion current density ifelectron diffusion coefficient is 265 cm2/s.
For the circuit shown in the Figure , consider silicon diodes with forward drop voltage of 0.7 V. If Vs = 150 Vrms and RL = 8 KN, the average value of load current is: 1:1 Vout Vs RL Oa. 8.413 mA Ob. 10.413 mA Oc. 12.413 mA Od. 14.413 mA ellee
nese gates Compatible 1Or state operatioOn? why 10- A certain logic gate has a VOLmax) = 0.45 V, and it is driving a gate with a VIL(max) = 0.75 V. Are these gates compatible for LOW-state operation? Why? 11