59. ssm Two metal beams are joined together by four rivets, as the draw- ing indicates. Each rivet has a radius of 5.0 × 10-³ m and is to be exposed to a shearing stress of no more than 5.0 × 10° Pa. What is the maximum tension T that can be applied to each beam, assuming that each rivet carries one-fourth of the total load? -Rivet

Q: Using Mohr's cirlce method Determine: a) Average normal stress. Au b) Maximum and minimum stress. c)…

A:

Q: Cross section of each bar 350 mm2 . Find stress in bar CD

A:

Q: es Required information Problem 01.061- A two link assembly with point loads Two horizontal 13-kip…

A:

Q: The Link AB must be made of steel with a maximum normal stress of 450 Mpa. Any stress above that…

A:

Q: steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: The given figure is shown below:

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

A:

Q: H 0000 B D 4 m 4 m 4 m

A:

Q: 3/4 130 mm O O O 25 mm 25 mm

A: Fbd is shown below Upper plate , bolt and lower plate fbd  Bolt is being cut by one plane as they…

Q: The maximum shear stress (kPa) is most nearly 100 kPa 50 kPa -50kPa 50 kPa 75 56 O 66 O

A: Given data : Normal stress in X direction (σX)=-50 KPaNormal stress in Y direction (σY)=-100…

Q: The maximum shear stress (kPa) is most * nearly 100 kPa 50 kPa -50 kPa 50 kPa 75 O 56 66 O E

A: σx = -50 kPa  σy = -100 kPa τxy = 50 kPa  To calculate the max. Shear stress in kPa

Q: please someone answer this with complete solution thank you

A:

Q: As demonstrated, four 25mm diameter rivets with a T=75kN axial load are equally distributed. The…

A: Shear stress in rivets: The plates are connected by rivets happens to exert tensile stress on the…

Q: A machine member is subjected to forces as shown in Fig. B 300- 3 kN-m 1.5 kN-m 20 kN Determine the…

A: A )  To find : Determine the stresses ? A problem of solid mechanics.

Q: A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN…

A: Given:- The magnitude of the force (P) = 4.5 kN The dimension variable (b) = 240 mm = 0.24 m The…

Q: A. Determine the depth of the compressiin block.(mm) B.Determine the nominal moment strength (kN-m)

A: Determine the depth of the compressiin block.(mm) B.Determine the nominal moment strength (kN-m)

Q: Q2: A shaft is subjected to a 40kN axial load. Determine the bearing stress between the shaft and…

A:

Q: 2. The lap joint that is 130 mm wide and 25 mm thick is connected by three 20-mm-diameter rivets.…

A: Given, d=20 mm Number of rivet n=3 Allowable shear stress = 65 MPa Bearing stress =45 MPa Maximum…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A:

Q: Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum…

A: Compute the polar moment of inertia, J maximum shearing stress in any rivet does not exceed 80 MPa.…

Q: d help wirh 3 and

A:

Q: A single strain gauge, placed in outer surface and at an angle of 30 gives a reading at point A of…

A:

Q: Horizontal Alignment An existing road with a design speed of 85 km/h passes from one tangent through…

A: Horizontal alignment is the positioning of a roadway, as shown in the plan view, using a series of…

Q: When the temperature is at 30°C, the A-36 steel pipe fits snugly between the two fuel tanks. When…

A: The temperature variation in the pipe is as shown below. The expression for the temperature…

Q: 1. From the given truss below, answer the following: 9 m G 4 m 135 kN 135 kN B 4 m C4m E Compute the…

A:

Q: B 5 m 5 m 5 m 5 m, 5 m A 5 m 5 m E 30 kN 20 kN From the given truss, which member has an internal…

A: We will employ method of joint to every joint untill we find the member having compressive force of…

Q: 1. A sign structure is subjected to the uniform wind loading of 2 kPa. Determine the stress…

A:

Q: 10 kN 20 kN 0.2 m -0.2 m -0.2 m- D= 50 mm c L.A D B RC Section A-A

A: Given:- D=50mm To find:- Max. compression and tension flexural stress

Q: 16-11. A newly designed transaxle was tested with strain gages to determine the maximum stress,…

A: Maximum stress measured using Strain Gage (σmax) = 40000 psiFactor of Safety = 3

Q: med joint by the g. Determine t

A: Dimension of block = 2.5in.*2.5in. Sliding angle = 55° Length of steel key = 2.5in.  Working Bearing…

Q: A T-beam with the cross-section shown above is subject to the loads shown. a) Determine the second…

A: Given:- To find:- Second moment of area SFD and BMD Normal stresses at A, B and C Concept:-…

Q: Problem 4: Given: Four-25-mm-diameter rivets with an axial load of T= 75 kN distributed equally as…

A:

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

A:

Q: The

A:

Q: At a given sectiona shaft is subjected to a bending stress of 30 MN/m2 and a shear stress of 60…

A:

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

A:

Q: "Determine thé forcés in all the members, and state if these meņmbers are in tension or compression.…

A:

Q: The isosceles right angled triangular truss ABC is held in place by the structure shown in Figure 3.…

A: Force in member AC Force in member CE

Q: 213. In structural practice, steel clip angles are commonly used to transfer loads from horizontal…

A: GivenForce,F=45kNDiameter of rivet=22mm