=515mm E'=25MPA =320MPA lu=420KN-m etermine As USE NSCP 2015, As = || sq.mm.

Q: Four interior angles of a five-sided polygon traverse A = 98°33'26",B = 111°04'37", C = 123°43'58", ...

A: Given : Angle A, B, C and D are given correct angles of a closed traverse. Angle E is to be found ou...

Q: The homogeneous bar AB weighing 2000 lb. is supported at either end by a steel cable. Calculate the ...

A: Given data in question  Length of bar Working stress of steel cable Weight of bar To find out  Small...

Q: |Q.6) The fuselage frame shown below is subject to P= 1000 lb vertical load offset from centerline b...

A: We have to determine the value of shear flow in the skins on the sides of the fuselage frame accordi...

Q: Suppose that in a senior college class of 500 students it is found that 210 smoke, 258 drink alcohol...

A:

Q: 1. A normal-weight concrete has an average compressive strength of 4500 psi. What is the estimated m...

A:

Q: A theodolite is set up at station A. The RL of instrument axis is 212.250 m. The angle of elevation ...

A:

Q: Mass Diagram 5000 4000 3,500 3000 2,100 6.0 2,100 7.0 2000 8.0 1,500 1,500 8.0 1000 1,100- 7.1 6.0 7...

A: Excavation is the most common way of moving earth, rock or different materials with apparatuses, gea...

Q: Design a circular slab for a room 5 m in diameter (effective) with simply supported edge. Total supe...

A:

Q: A 300mm x 425 rectangular beam is reinforced for tension only with 4-28mm bars. The beam has a concr...

A:

Q: General Directions: Read each questions and directions carefully and write your answers and solution...

A:

Q: The rated speed of the vehicle is the maximum speed the vehicle can round a curve relying on frictio...

A: The given statement is True The maximum speed the vehicle can round a curve relying on friction forc...

Q: Please explain every detail to me on how they get the 45 that I encircled in a blue pen. Thank you s...

A:

Q: Using your prior knowledge in Geometry and Trigonometry, solve for the Azimuths of the following: (S...

A: To Determine a. Direction from A to B b. Direction from B to C C. Direction from C to D d. Direction...

Q: As shown below a rectangular R.C.C. column is subjected to compressive force P at an eccentricity of...

A:

Q: . Assume wall height to be 3.0 m openings at: a. common area Doors (0.9x2.1), windows (1.2x1.2) b. t...

A:

Q: 4. An incandescent lamp has a tungsten filament whose resistance is 96 ohm at its operating temperat...

A: α=4×10-3/°C R2900=Ro(1+4×10-3×2900) R24=Ro(1+4×10-3×24) R24R2900=1+4×10-3×241+4×10-3×2900 R24=0.0869...

Q: Draw the FDBS of member ADB and BEC 1 m 1 m В |C E 1 m D 1.6 m

A: To Determine Free body diagram of members ABD & BEC

Q: gular channel

A: Given:- width=4m width=2m depth=1m To find:- flow and depth in the 4m section  

Q: Determine the available strength of a 10.0 ft double-angle compression member using A36 steel. 7oal:...

A: Given:- Two 5×3×1/4 angles are used back-to-back with a 3/8 in the gap The two angles are welded to ...

Q: Given the following data gathered from an altimeter survey: Elevation of the high base, 818 m, eleva...

A:

Q: 5MN/m^2, find the maximum uniformly distributed lateral load the beam can support (Densit

A:

Q: water quality discussion questions: Q1- explain how can natural factors contribute to the change in ...

A: Water quality refers to the chemical, physical, and biological properties of water depending on its ...

Q: A kN A kN -4.5- -13.5-- FIGURE NO. 1

A:

Q: Ssoollv

A: A turbojet does not consist of which of the following component? a) compressor b) combustion  chambe...

Q: Complete the differential level notes shown below, and determine the height of instrument of the sec...

A:

Q: The column shown in the figure is fixed atthe base and free at the upper end. A compressiveload P ac...

A: Given:- Column To find:-  the maximum deflection d of the column and the maximum bending moment Mmax...

Q: A square plastic bar (length Lp, side dimensions p = 193 mm) is inserted inside a hollow,square, cas...

A: Step 1: To find x: X =200 – 193 – 2x3 =1 mm Lateral strain = 1/193 = 5.181 x 10-3 Axial strain = -5....

Q: columns CD and DE for the braced frame shown. Assume the beams are 12 in x 20 in and the columns are...

A:

Q: Consider an inner beam-column joint in the ground floor roof of a eight storey building in Noida, U....

A:

Q: D C В 10 kN 4 kN/M 2.5 M 2.5 M 2.5 M 2,5 M 1.0 M 2.5 M

A: A. DETERMINE SUPPORT REACTION B. DETERMINE STRESS IN THE CABLE C. DRAW FREE BODY DIAGRAM

Q: The maximum number of ways to solve a structure with single degree of indeterminacy using MCD (Force...

A: For every degree of indeterminacy, we must have a redundant force (internal or external). So, for a ...

Q: Given the following: b=355mm d=575mm fc'=27.5MPA fy=275MPA Mu=670kN-m Determine As A. USE NSCP 2015,...

A:

Q: Consider an inner beam-column joint in the ground floor roof of a eight storey building in Noida, U....

A:

Q: A box contains 500 envelopes, of which 75 contain $100 in cash, 150 contain $25, and 275 contain $10...

A:

Q: Problem#1) For the post-tensioned beam shown in the figure find the maximum usable moment capacity a...

A: Aps =1.53 in2 As per ACI 318-19, fps =270 (1-(0.28/0.75) (5.34x10^-4)(270/6) =268.96 ksi Compression...

Q: 9. A square lamina (each side equal to 2m) is submerged vertically in water such that the upper edge...

A:

Q: By analogy, rectilinear motion formulas with constant acceleration can be used to derive the formula...

A:

Q: 2. A machine costs PhP 300,000 with a salvage value of PhP 50,000 at the end of it's life of 10 year...

A:

Q: Why should a number 2 pencil not be used in field notekeeping?

A: Field notes are handwritten documentation of fieldwork completed at the time. Field notes should be ...

Q: list 5 type. of Kolice anod their uses ià water and oat anginecaing

A:

Q: Three wires AD, BD and CD having the same cross- sectional area and of the same material support a l...

A:

Q: Describe the different methods of calibrating pressure gages/instruments ?

A: Concept- Pressure calibration is the comparison between the readings shown by the instrument and the...

Q: Which of the following is/are accelerated methods of depreciation: (A) Straight- Line Method; (B) Si...

A:

Q: With the condition that a block on top of a table, its kinetic friction is greater than its static f...

A:

Q: 16.22 Determine the member end moments and reactions for the frames shown in Fig by using the slope-...

A:

Q: For the given beam below, determine the required tension steel area of the bottom bars for the posit...

A:

Q: 2. A yield measure with a volume of 0.248 ft has a weight of 7.69 lb. When filled with a sample of t...

A:

Q: Problem: Design the reinforcement for the short column shown with f'c = 4000 psi and fy = 60000 psi....

A:

Q: A golfer hits a golf ball with an initial velocity of 48 m/s at an angle of 25° with the horizontal....

A:

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.