50 mim 150 mm 50 mm 150 mm 400 mm 400 mm 150 mm'150 mm Prob. 10-99

Q: 184 What is the strain energy of the massless stepped bar as shown in the figure below? [Take E= 200…

A: Strain energy of the massless stepped bar Take E=200Gpa

Q: Bar ABC has an outer diameter of 10 mm and is made of red brass for which E = 100 GPa. Section AB is…

A: Consider the BC portion of the beam:

Q: Velocity profile inside boundary layer is given as, U Ty = sin - sin U. 2 8 Find the value of

A: Following is the given velocity profile:

Q: A=(5i–6j–k)m B=(-5i+8j+6k)m

A:

Q: Steel railroad rails 8m long are laid with a clearance of 4mm at a temperature of 10°C. At what…

A:

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: To Find :- flexural stress at bottom fiber Given data:- a = 50 mm, b= 110 mm, c= 70 mm E = 140 GPa =…

Q: Given the thin-walled cross-section in figure 2 (dimensions in mm) with thic equal to 1 mm,…

A: Given the below thin walled section with thickness of members= 1mm:

Q: Two elastic bodies made of different materials are placed in a rigid cavity and their surfaces are…

A: The elastic modulus is the slope of its stress-strain curve in the elastic deformation region.…

Q: The Reynolds Number is a dimensional quantity that indicates if the fluid flow is laminar or…

A: Reynold number is a number which generally indicates what type of flow is their . Reynold number…

Q: A flat bar 10 mm thick and 100 mm wide is subjected to a pull of 100 kN. One side of the bar is…

A:

Q: 4. Two bars are placed as shown. First, indicate if the bars are "in parallel" or "in series" and…

A:

Q: Determine the Volumetric Strain of the material shown, if E=100 GPa and v-D0.25 40 MPa X- 40 MPa O…

A:

Q: Steel railroad rails 10 m long are laid with end-to-end clearance of 5 mm at a temperature of 18°C.…

A:

Q: PROBLEM 3 Determine the centroidal moment of inertia, Ixx of the cross section shown. 6 in H .5 in…

A: Built up section is given and it has been asked to determine moment of inertia about x axis. Please…

Q: 3.1.2 The block shown is made of a magnesium alloy for which E = 45 GPa and ν = 0.35. Knowing that…

A: Consider the stress strain relations for a homogeneous isotropic in 3D as follows Strain in…

Q: Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the…

A:

Q: QIJ Give the reason behind the followings: 1.Piczometers cannot be used to measure the vacuum…

A: Pressure in real is defined as the force per unit area zone, or the stress at a point inside a…

Q: 2. Solve for the centroidal distances of the figure shown.

A: Centroidal distance of x- coodinate:x=A1x1+A2x2-A3x3A1+A2-A3

Q: What is the strain energy of the massless stepped bar as shown in the figure below? [Take E = 200…

A:

Q: stress tensor at a point is given by the following 6x = 40 oy = 30 oz = 20 MPa, Txy 20 MPa, ryz 40…

A:

Q: The band in the figure below is stainless steel (coefficient of linear expansion = 17.3 ✕ 10−6°C−1;…

A:

Q: A STRAIGHT LINE IS DETERMINED TO BE 3234.25 m WHEN MEASURED WITH A 50-m STEEL TAPE SUPPORTED…

A: Measured distance (L) = 3234.25 mLength of steel tape(l) = 50 mPull during measurement (Pm) = 4.5…

Q: 28.30mm 28.20mm чомра 6-A 20mm by 20mm square is etched onto a metal bar prior to loading. Upon…

A: To find Poisson ratio and Young's modulus

Q: There two parallel discs, one is up and another is down, whose diameters are both d. The thickness…

A:

Q: A line was determined to be 2395.25 m when measured with a 30-m steel tape supported throughout its…

A: The given data is: Corrected length, L=2395.25 m Measured temperature, Tm=35 degree Measured pull,…

Q: Determine the (centroidal axis) 0 is 20 in O 1.74x10^6 in^4 0.94x10^6 in^4 2.54x10^6 in^4 3.74x10^6…

A: Given data  Dimensions  To find Moment of inertia

Q: 50 mm C 175 mm B. -225 mm -300 mm Bar ACB shown in the Figure is subjected to a uniform temperature…

A:

Q: The steel plate shown below is put in into a rigid chamber, such that spacings of size s- 0.003 m.…

A: To Determine Increase in temperature along x-axis to just close the spacing on the right in degree…

Q: 80° F 160° F -10 ft- †10 in.

A: Given data : Simply supported beam with pinned and roller support at  A and B Find : Vertical…

Q: Q2: Determine completely the resultant R of the three forces shown in the figure below. 60 kN 100 kN…

A:

Q: Consider the cross-sectional area shown. Suppose that h= 60 mm. Determine the location y of the…

A: The centroid is the center of mass of the section of beam. It is considered as the center point of…

Q: A rectangular piece of material is subjected to tensile stresses of 83 and 65 N/mm² on mutually…

A: Given data : σ1=83 N/mm2σ2=65 N/mm2ν=0.3E=200000 N/mm2

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.