50 kN B. 3 m -1m :12 mm 10 mm 250 mm 12 mm 200 mm

Q: 5. Determine the normal stress and shear stress acting on the inclined plane AB. Soive the problem…

A:

Q: The state of stress at the point can also be represented in termsof the maximum in-plane shear…

A: False, The state of stress at the point cannot be represented in terms of the maximum in-plane shear…

Q: 6kN and 1.0kNm loads are applied to the top of the 62-mm-diameter cast-iron as shown. Determine the…

A:

Q: Take the section AB, construct the FBD and label the internal loadings, determine the normal stress…

A:

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

A:

Q: (e) E = бу 30 MPa Txy 85 MPa Ox 120 MPa = =

A: GivenPart eσx=-120MPaσy=30MPaτxy=85Mpa part fσx=30MPaσy=-80MPaτxy=15Mpa

Q: ) If the load has a weight of 600 lb, determine the maximum normal stress developed on the cross…

A: An internal resisting force which is applied by the molecules of the object so that the shape of the…

Q: Determine the normal and shear stresses at point B. 5-10 min 180 mm 180 mm 60 mm - 30 KN

A: Given data dimension of cross section = 180mm× 60 mm find the normal and shear stress at point B.

Q: The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on…

A:

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

A:

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: At point A & C, the beam is pin connected. Therefore, find the average normal stress in the…

A:

Q: The stepped steel shaft carries the torque T. Determine the allowable magnitude of T if the working…

A: Answer: The magnitude of allowable torque is 933.0530 N•m.

Q: 1. The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A…

A: To find: The longitudinal and hoop stress developed in the wall of the pipe, also draw the stress on…

Q: The shear stress is maximum on the principal plane Select one: True O False

A:

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

A:

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: The rectangular bar carries a load of P = 102 KN and is connected to the support bracket with a…

A:

Q: Determine the maximum shear stress If maximum principal stress=50 MPa, Minimum principal Stress=20…

A:

Q: Two fully loaded tractor trailers travel over the bridge putting substantial loading on the…

A: The objective of this question is to calculate the shear strain at point T when a vertical…

Q: 3-Determine the maximum vertical force P that can be applied to the bell crank so that the average…

A:

Q: 13/ 12 a 1 m 2 m a

A:

Q: 9-74 If the box wrench is subjected to the 50 lb force, determine the principal stresses and maximum…

A:

Q: The grains of wood in the board make an angle of 20 with the horizontal as shown. Using Mohr's…

A:

Q: In each case, the state of stress sx, sy, txy produces normal and shear stress components along…

A: (a) sx'=-5 kPasy'=0τx'y'=8 kPau=20°   The stress along the normal -axis:…

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: The solid circular rod has a cross-sectional area of 360 mm². It is subjected to a uniform axial…

A:

Q: The solid bar has a diameter of 50 mm. The two forces and the x-y-z coordinate system which is…

A:

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A:

Q: Determine the stresses at points A and B as a results of applying each of the following internal…

A:

Q: 5. Two forces act on the solid circular rod (r=.005 m) as shown. Using Mohr's circle, determine the…

A: Draw mohr circle and find principal stresses and maximum shear stress.

Q: The wide-flange beam is subjected to the 50-kN force. Determine the principal stresses in the beam…

A:

Q: The clamp presses the smooth surface at E when tightening the screw. If the tension in the bolt is…

A: Given data as per question Tension in the bolt =40 kN   Support reaction are shwn on FBD (a)Internal…

Q: Determine the principal stresses in the beam at point A. Specify the orientation of the element…

A: here's how to analyze the stress at point G:Information Needed:Beam geometry (width and…

Q: Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a…

A: Here, Shaft diameter = dsh = 50 mm Allowable shear stress in shaft = τsh = 100 N/mm2 Pitch circle…

Q: The steel rod has a circular cross section. If it is loaded by a 500 lb vertical force as shown,…

A: