50 400 50 80 500 340 60 80- 500 X

Q: Measured infiltration rates, f in cm/hr, for every hour from t=0, when the rainfall just commenced…

A: Given,fo=2.2 cm/hrfc=final constant rate of infiltration=0.7 cm/hrk=4 day−1=4/24hr−1=1/6hr−1Horton's…

Q: H = μA In the figure, he, hr, z and the measured slope length I were 5.64 ft, 5.42 ft, 96° 18'56",…

A: Reference : Survey Engineering, Distance measured by Total station Refer above figure ; (mentioned…

Q: compute the deflection at the center due to the 36 kn load induced at midspan of 4m simply…

A: As per guidelines, the question has been solved by first method only i.e. Integration method

Q: The body on the 30° incline is acted upon by a force P inclined at 20° with the horizontal. If P is…

A:

Q: Q6: Consider the figure below, the cross sectional area A of a gutter with equal base and edge…

A: Given ,            A= 4 sin@(1+cos @)                 (θ= @)

Q: Consider the frame shown in (Figure 1). F₁ = 850 N Figure C 2m-

A:

Q: Situation 35 Determine the maximum value of load P if the thickness of the steel section provided is…

A:

Q: A C9 x 20 with 2 lines of 7/8-in diameter bolts in the web as shown in the figure. Fy = 36 ksi and…

A: Given data: Properties of C9x20 section -  Ag = 5.8 in2d = 9 intw=0.448 inbf = 2.65 intf =0.413 intw…

Q: You are an engineer working on a project and your prototype has failed prematurely. You question…

A: Given data Do=0.501 in lo=2 in

Q: a new cast iron pipe must carry 1.2m^3/s at a head loss of 5m per km length of pipe.Compute the…

A:

Q: how to calculate u value of shed roof? Which formula? can you give example of calculation

A: The U-value is the number that is assigned to a section of the building that includes roof, walls…

Q: Situation 36 Considering the contraption shown in figure, AB = 450 mm, BC = 225, mm BD = 480 mm, CE…

A:

Q: Compute the increase in the stress at point A when two line loads of value 90 kN/m and 325 kN/m act…

A:

Q: Given the following elements of a circular curve: middle ordinate = 2 m; length of long chord = 70…

A: Circular curve  Length of long chord (L) = 70m  Mid ordinate (M) = 2m  Determine the degree of curve…

Q: A rectangular beam having a width of 300 mm has an effective depth of 600 mm. Total depth of the…

A: As per our policy, the first two parts are solved within the stipulated time. Please post the…

Q: 8. A soil particle is subjected to a maximum stress of 14.6 kPa and a minimum stress of -4.18 kPa.…

A: The state of stress on a given soil particle. Maximum stress and minimum value of stress viz.…

Q: Discussion about carbon nanofiber in water treatment

A: Carbon nanofibers have gained significant attention in the field of water treatment due to their…

Q: Consider a frame subjected to loads as shown. Determine the reactions at the supports and draw the…

A:

Q: define in your own words each of the "5 D's of Development": Density, diversity, design, destination…

A: Planning and policy that incorporates the 5 D's of development can promote health and well-being…

Q: 3. The manufactures wood beam carries a uniformly distributed load of intensity Wo Determine the…

A: Shear stress in the wood is limited to 300 psi.

Q: F6-8. Determine the force in members LK, KC, and CD of the Pratt truss. State if the members are in…

A: Determine the force in member LK, KC and CD of the truss.

Q: A six-lane divided highway is to be designed to replace an existing highway. The present AADT (both…

A:

Q: A circular footing is 2.37 meters in diameter. The bottom the footing is 2.69 m. below the ground…

A: The ultimate bearing capacity of the soil is defined as the minimum gross pressure at which the soil…

Q: 6. The flow and density of a highway were observed to follow the triangular model as given below:…

A: The flow and density of a highway were observed to follow the triangular model as given below,…

Q: Determine the force P exerted on the twig G. Note that there is a horizontal line of symmetry for…

A: A tool which applies a load at twig G Line of symmetry exist for handle but not for jaws

Q: Appendix 1 shows a structural drawing of the first floor of a random building. The labels "C"…

A: Section 200 UB 29.8 The concentrated point load acting on the beam is 12 kN

Q: 5-67. The uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three…

A:

Q: escribe (a) how public transportation facilities have influenced urban form and land development in…

A: Urban transportation refers to the movement of people and goods within urban areas with high…

Q: Measured infiltration rates, f in cm/hr, for every hour from t=0, when the rainfall just commenced…

A: Table for infiltration rate: Rainfall commenced to t = 8 hours are given in table. Initial constant…

Q: Define GIS.

A:

Q: Questions G,H,I,J

A: Line Length, ft Azimuth AB 721.08 326o18'37" BC 922.02 282o31'43" CD 939.31…

Q: function and determine the feasibility of 10° possible solu er of variables N such that the compute…

A: Given:- Variables X1,X2,Xn To find:- greatest number of variables

Q: 1. A 5-m beam simply supported at the ends carries a concentrated load of 90 kN at midspan. Select…

A: Length of beam, L=5 m Concentrated load, W=90 KN Allowable stress, σallo=50 MPa=50 N/mm2

Q: For structure shown, compute the reactions and draw shear and bending moment diagrams. Indicate…

A: Given a statically determinate beam inclined at a given angle.  Required : Reactions, Shear and…

Q: 9. A 4.5 m saturated clay layer (two-way drainage) subjected to surcharge loading underwent 90%…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: B: A finite element model of a cantilever beam subject to loading and moments is given by optimizing…

A: f (x,y) = 5x2 _ 5xy + 2.5y2 - x - 1.5y As shown below, MATLAB gives: x = 0.5, y = 0.8 and fmin =…

Q: }}} solve by method slope deflection my L1 W L2 L3 determine a general eguation in beam MA, MB, MC,…

A: Using the slope deflection method: Fixed end moments: Span AB: MFAB=-wl212=-WL1212MFBA=wl212=WL1212…

Q: 3.5 through 3.13 Determine the reactions at the supports for the beam shown. 30 kN/m A FIG. P3.5 10…

A:

Q: 4) Compute the deflection at the center due to the 36 kN load induced at midspan of 4m simply…

A: The given beam is statically determinate beam and can be analyzed using the equations of…

Q: PROBLEM A truck with axle loads shown rolls across a 10-m span. Compute the maximum bending moment…

A: we have to determine the maximum bending moment and maximum shearing force

Q: Figure Q2 shows a 2-dimensional truss. The area of each member is equal to A. The modulus of…

A: Find: (a) Degree of freedom (b) Transformation matrix (c) Global stiffness matrix

Q: Design will be carried out as per provisions of TS 500 1 kb = 1300mm d=560km +250 + Inf =120mm…

A:

Q: Determine the support reactions and member forces of the trusses shown.

A:

Q: 8. A soil particle is subjected to a maximum stress of 14.6 kPa and a minimum stress of -4.18 kPa.…

A:

Q: For the simple beam shown, use the virtual work method to find (a) the location and value of the…

A: using Virtual work method##  Calculation of location and value of maxm Rotation and  maxm Deflection…

Q: Problem-1 Determine the support reactions and draw the bending moment and shear diagrams of the beam…

A: A statically determinate beam with a varying load on it To find : Shear and moment diagrams with…

Q: II. Determine the moment over the support B of the beam shown using Three Moment Equation. A 300…

A:

Q: A rectangular “Apitong” beam 50mm x 300mm is used as a simply supported beam 3.2m long. Determine…

A: Given a simply supported beam with uniformly distributed load of intensity say "w" kN/m The…

Q: Engineering strain of a mild steel sample is recorded as 0.100%. The true strain is 1. 0.010% 2.…

A: Mild steel sample- Strain ε=0.100%ε=0.100100

Q: The common tangent CD of a reversed curve is 280.5m and has an azimuth from the south (s)of 312°…

A: