5.23. Refer to Fig. 5-24. The body A weighs 32.8 lb and rests on a smooth surface. The body B weighs 14.3 lb. Determine the tensions in S, and S, and the normal reaction of the horizontal surface on A. Ans. S, 12.4 lb, S₂ = 14.3 lb, N= 25.7lb P P(Vertical) B 30° B

Q: Forces of magnitude F; =7 kN in the +y direction and F 2 =13 kN in Question 2) the -z direction are…

A:

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: y

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: 3 just wearing his suit so you know he's an astronaut, is holding a space space chest along with the…

A: M = 761 g  h = 0.6m          a     distance between E to B         d = 0.7 2+0.62        d =0.92 m

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: can you answer 1B

A:

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: 2.36x178×106 1- 1 0.9x300x368²×30 Prequired 400 (1.18 30)

A: Given Data⇒

Q: 3. The shaft AB is made from L2 tool steel (shear modulus 75 GPa), has al diameter of 40 mm, and is…

A: Given data  Shear modulus= 75 GPa  Diameter= 40mm Find the maximum shear stress in AB and BC

Q: س 19/ 1 درجة en force 90 N and angle 50° on the axis (Y

A:

Q: The collar A slides along the rotating rod OB. The angular position 2 of the rod is given by 0 =…

A: Given data:- thetha = 2/3 ×π t^3  rad. R = 18t^4+4 m find the velocity and acceleration vector.

Q: Determine the angle 0 between the edges of the sheet-metal bracket. -400 mm 250 mm 300 mm 50 mm y

A:

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: Which of the points is located in the third quarter? Supplementary material: A, E2 D, B;B2 2. E, A2…

A: Solution:   There are four quadrants. In Quadrant 1: x and y both are positive. In Quadrant 2: x is…

Q: Fint total force acting on point A. Point A can be anywhere.

A:

Q: how can I get the 85 α

A:

Q: (Determine the (f_x ) when force 80 N and angle 30° on the axis (X .A 69N .B 69.28lb .C 69.28N .D…

A:

Q: Describe the Parallel-Axis Theorem for an Area?

A:

Q: Fy = 16 kN O Fy = 4 kN O Fy = 2 kN O

A:

Q: A piezometer and a pitot tube (close to each other, as described in the figure) are connected to the…

A:

Q: ********** QI/A/ The 4-mm diameter cable BC shown in Figure Q1-4 is made of a steel with E-200 GPa…

A:

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: 50 mm 150 mm 50 mm 85 mm Section X-X 20 kN

A: Let us shift the load to section X-X. The moment M and force P will create the same effect.

Q: PROVE THAT THE ANGLE IS 30° BY LAWS OF CONGRUENCY

A:

Q: Isn't the area of the circle equal to pi times the square of its radius?

A: Explanation: Since the diameter ( d )  of steel bar is given, area of the circle is in terms of…

Q: F = 120 lb | 30° 12 kN 1.25"- 30 4 m 1.5" 5 m 11"

A:

Q: slove f

A:

Q: M, B

A: Given data, The reaction at A and B can be calculated as -

Q: Figure 1 of 1 30 40 F2

A: Given, F1 = 210 N F2 = 510 N Angle between two forces = θ = 40°

Q: What is the normal force applied to the block?

A:

Q: Through the two pipes in Figure 6 flow equal flows of water. data: Pipe diameter No. 1: 200 mm -…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.