5. Please clearly indicate what the written in answer is 4.00 Ω ● 1.60 m ● Magnetic field is outward (.) →Fapplied A highly conducting bar moving with speed 6.00 m/s, in perfect electrical contact, moves along frictionless conducting rails connected to a 4.00- resistor as shown in the figure. The length of the bar is 1.60 m and a uniform magnetic field of 2.20 T is applied perpendicular to the paper pointing outward, as shown. At what rate is energy dissipated in the 4.00 Q resistor? Answer to three significant digits.

5. Please clearly indicate what the written in answer is 4.00 Ω ● 1.60 m ● Magnetic field is outward (.) →Fapplied A highly conducting bar moving with speed 6.00 m/s, in perfect electrical contact, moves along frictionless conducting rails connected to a 4.00- resistor as shown in the figure. The length of the bar is 1.60 m and a uniform magnetic field of 2.20 T is applied perpendicular to the paper pointing outward, as shown. At what rate is energy dissipated in the 4.00 Q resistor? Answer to three significant digits.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter13: Electromagnetic Induction

Section: Chapter Questions

Problem 41P: In the circuit sho in the accompanying figure, the rtd slides along the conducting rails at a...

See similar textbooks

Similar questions

In the August 1992 space shuttle flight, only 250 m of the conducting tether considered in Example 23.2 could be let out. A 40.0 V motional emf was generated in me Earth’s 5.00105T field, while moving at 7.80103m/s. What was the angle between the shuttle’s velocity and the Earth’s field, assuming the conductor was perpendicular to the field?
(a) What is the speed of a supersonic aircraft with a 17.0-m wingspan, if it experiences a 1.60V Hall voltage between its wing lips when in level flight over the north magnetic pole, where the Earth's field strength is 8.00105T ? (b) Explain why very little current flows as a result of this Hall voltage.
In the circuit sho in the accompanying figure, the rtd slides along the conducting rails at a constant VelOCity v. The velocity is in the same plane as the rails and directed at an angle 6 to them. A uniform magnetic field Bis directed out of the page. What is the emf induced in the r?
A current of 1.2 A is flowing in a coaxial cable whose outer radius is five times its inner radius. What is the magnetic field energy stored in a 3.0-m length of the cable?
(a) A DC power line for a light-rail system carries 1000 A at an angle of 30.0° to the Earth’s 5.00105-T field. What is the force on a 100-m section of this line? (b) Discuss practical concerns this presents, if any.
Hall potentials are much larger for poor conductors than for good conductors. Why?
The magnetic flux through the loop shown in the accompanying figure varies with time according to m=2.00e3tsin(120t) , where m is in milliwebers. What are the direction and magnitude of the current through the 5.00 resistor at (a) t= 0; (b) t=2.17102 s and (c)t=3.00 s?
Unreasonable results Frustrated by the small Hall voltage obtained in blood flow measurements, a medical physicist decides to increase the applied magnetic field strength to get a 0.500-V output for blood moving at 30.0 cm/s in a 1.50-cm-diameter vessel. (a) What magnetic field strength is needed? (b) What is unreasonable about this result? (C) Which premise is responsible?
A 0.50-kg copper sheet drops through a uniform horizontal magnetic field of 1.5 T, and it reaches a terminal velocity of 2.0 m's. (a) What is the net map,-, eh: force on the sheet after it reaches terminal velocity? (b) Describe the mechanism responsible for this force, (c) How much power is dissipated as Joule heating while the sheet moves at terminal velocity?
Check Your Understanding Consider using Ampere’s law to calculate the magnetic fields of a finite straight wire and of a circular loop of wire. Why is it not useful for these calculation?
The density of charge carriers far copper is 8.471028 electrons per cubic meter. What will be the Hall voltage reading from a probe made up of 3cm2cm1cm ( (LWT) ) copper plate when a current of 1.5 A is passed through it in a magnetic field of 2.5 T perpendicular to the 3cm2cm .
Verify than the direction of the line force in an MHD drive, such as that in Figure 22.32, does not depend on the sign of the charges carrying the current across the fluid.