5. Draw the sketch of the following cross section of channel and indicate the specifieddimensions.a Semi-circular section with radius r = 3.0mb Rectangular section : b=4.0m, and d = 2.0mC Trapezoidal section : Bottom width b = 3.0md = 2.0mDepth :Side Slope : 2 horizontal to 1 verticali. Calculate the area (A), wetted perimeter (P)and the hydraulic radius (R) of eachchannel.ii. If the discharge of these three channels are equal to 6.0m/s, determine the velocityof water flowing of each channel and identify which channel has the highest value ofvelocity 2, the lowest value of velocity ?

Answered: Image /qna-images/answer/97c37c4f-91ee-4fcb-b916-ae8172d6924a.jpg

5. Draw the sketch of the following cross section of channel and indicate the specified dimensions. a Semi-circular section with radius r = 3.0m b) Rectangular section : b=4.0m, and d = 2.0m C Trapezoidal section : Bottom width b = 3.0m Depth : Side Slope : 2 horizontal to 1 vertical d = 2.0m i. Calculate the area (A), wetted perimeter (P)and the hydraulic radius (R) of each channel. ii. If the discharge of these three channels are equal to 6.0m/s, determine the velocity of water flowing of each channel and identify which channel has the highest value of velocity 2, the lowest value of velocity ?

5. Draw the sketch of the following cross section of channel and indicate the specified dimensions. a Semi-circular section with radius r = 3.0m b) Rectangular section : b=4.0m, and d = 2.0m C Trapezoidal section : Bottom width b = 3.0m Depth : Side Slope : 2 horizontal to 1 vertical d = 2.0m i. Calculate the area (A), wetted perimeter (P)and the hydraulic radius (R) of each channel. ii. If the discharge of these three channels are equal to 6.0m/s, determine the velocity of water flowing of each channel and identify which channel has the highest value of velocity 2, the lowest value of velocity ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the volume of the cut if the the area of a cross section of a profile 216 mfrom the initial section is 56.1 m2. Use End Area method
please solve for h and explain...thanks!
Question 2. Below shown is the profile for a road construction at a station. This is a fill section. Sometimes the letter C is used to designate cut and F to indicate fill for the vertical distance or depth. In other words, a point below the base would have a negative sign in a fill section. F 11.8 below corresponds to -11.8 ft. The baseline is 50ft. Calculate the area for the fill section. (Answer: 137.3 yd²) 50ft F 11.8 -42.5 F 14.3 -32.0 0 -25 25 olo F 15.8 25 25 Baseline F 16.3 65.4
Solve the following using Double Integration method with slope form.Show clear and complete solution.
A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005m long at 20°C under a 50 N pull supported at both ends. During measurement the temperature is 5°C and the tape is suspended under a 75 N pull. The line is measured of 3% grade. What is the true horizontal distance? E = 200 GPa, cross-sectional are of tape is 3 mm² and coefficient of linear expansion is 0.0000116 m/°C.
Survey
Fill in the blanks Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that the water strikes at B. VA = 40 ft/s 4 ft - 1 attachment - 8 ft
In the figure below, determine the area included between the base line and the irregular boundary. 8.5 8.3 illing 4.5 2.5 3.0 6.0 2.0 3.9 4.2 2.2 6.0 5.9 9.0 11.6 Base Line ABC Note: All dimensions are in meters. Trace of the Irregular Boundary 8.3 5.1 4.6 11.2 4.8 5.5 X 10.2
Find area T, A, P, R, and D for the following compound section. 1.2 m - 0.8 m 0.3 m
Show step by step solution
Hello kindly please help me answer this question. Letter D. The other paper attached is for reference of datas
Use only Direct Integration Method 2. AF K M 2 B kN/m 60 mm * MM त्र d 3 EI= 5x10² KN m² Sc 0₂= 1)