5. A 4m simply supported laminated wood beam consist of eight 35 mm by 180 mm planks glued together to form a section 180 mm wide by 280 mm deep, it carries a uniformly distributed load of 5 KN/m and a 40 KN concentrated load at midspan. At 0.8 m from the left support, determine y b 35 mm (typ) a. Average shear stress in the glue joints at b, c, and d. b. Maximum shear in the beam C. Maximum flexural stress in the beam d 280 mm 3 180 mm

5. A 4m simply supported laminated wood beam consist of eight 35 mm by 180 mm planks glued together to form a section 180 mm wide by 280 mm deep, it carries a uniformly distributed load of 5 KN/m and a 40 KN concentrated load at midspan. At 0.8 m from the left support, determine y b 35 mm (typ) a. Average shear stress in the glue joints at b, c, and d. b. Maximum shear in the beam C. Maximum flexural stress in the beam d 280 mm 3 180 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PLEASE ANSWER IN 20 MINS
The beam shown has a 30-ft. simple span; f’c = 5,000 psi, fps = 250,000 psi, and the initial prestress is 160,000 psi. Assume fpy = 0.85 fpua. Find the concrete stresses in the top and bottom of the beam at midspan immediately after the tendons are cut;b. Assume 20% prestress losses in the tendons, find the new stresses at the top and bottom at midspan;c. Find the maximum service live load that the beam can support if allowable stresses of 0.60f’c in compression and 12√?′? in tension are permitted.
Q.1 Determine the short and long term camber of 8ST36 having a span of 75 feet with only self weight acting. Assuming concstant eccentress of pre-stressing reinforcement. The self-weight of beam can be taken at 594 lbs/ft.Assue creep co-efficient equal to 2.5 and free shrinkage sstrein of -0.40x10-³ in/in. Initial jacking stress may be 0.75 FPU.Fc' may be taken as 5000 psi and that at transfer at 3500 psi. The beam has 14, ½ low relaxation strands.what can be the deflection if superimposed DL is 60 psf?
A pretensioned prestressed concrete beam of span 6.8 m and of size 360 mm x 600 mm is subjected initially to a prestressing force of 1650 kN provided at an eccentricity of 160 mm through out by a straight cable. Area of steel provided is 1650 mm². The beam is subjected to live load of value 20 kN/m. Calculate loss of stress in reinforcement due to different reasons. M50 concrete is used. E=2x105 N/mm²; p = 1.6
3rd: A simply supported 12-m span beam, 300-mm wide by 550-mm deep, is pre- stressed by straight tendons with Aps = 774 mm² located 70 mm from the bottom at an initial prestress of 1.10 GPa. What maximum service uniform live load can the beam support in addition to its own weight if allowable tensile stress in concrete 0.5 x square root of f'c is permitted. after 17% loss Write your answer in 2 decimal places only. Use fc = 30 MPa unit weight of concrete 24 kN/cu.m. Sign convention is (+) tension, (-) compression. Indicate the sign in your final answer.
Design the slab reinforcement if the maximum positive moment is Mup=wul2/11 . and the maximum negative moment is Mup=wul2/11. Include the strain and temperature reinforcement. Given: Length=10.9m Span=3m Load combination(Wu) = 12.60 kN•m
For a simply supported prestressed concrete bearn, compute the stress in the top fiber at midspan due to prestressing force and service loads after transfer. Loss of prestressing force = 20%. Properties of the beam are: Width of the bearn, b: 242 mm; Depth of the %3D beam, d: 417 mm; Concrete cover of the bearn, cc: 61 mm; Prestressing Force, P: 574 KN; Superimposed Load, w: 14 KN/m; Length of the beam, L: 9 m. Stress is in unit MPa. Write only the value of your final answer. w (including selfweight) W „P.
SIMPLE 100 KN 50 KN STRESSES В 7.00 2. How many rivets are required to member BD to the gusset plate at H A Joint B? The maximum E shear stress of steel 4.00 2.00 3.00 4.00 rivet is 60 MPa. Compute the minimum safe quantity of rivets. 50 KN 50 KN
1. The cylindrical steel column has an outer diameter of 90 mm and inner diameter of 80 mm. The column is separated from the concrete foundation by a square bearing plate with the dimension of 160 mm x 160 mm. The working compressive and tensile stresses are 180 MPa and 200 MPa respectively, while the working bearing stress of concrete is 10 MPa. Find the largest force P that can be applied to the column. P Steel Concrete Foundation Bearing Plate
pre stressed conc. solution pls answer
Determine maximum shear and momentum of the beam load. Compute the value of the concentrated load. Using rule of thumb find initial size of beam Design a monolithic reinforced concrete Picture below for reference