5) What is IC,max(open), the current that flows through the capacitor whose magnitude is maximum during the time when the switch is open? A positive value for the current is defined to be in the direction of the arrow shown. A Submit
Q: + P 0.8 pf lagging V₂ P₂ 0.9 pf lagging ?For the circuit shown above, what is the input power factor…
A:
Q: Determine the values of 12, 14, V2, V3. and V6 in Fig.(2). 4 V 3A 6V A 2A -2VD Fig(?)
A: In this question we need to find an unknown voltage and current shown in the given circuit by using…
Q: In this Zener diode regulator, the source voltage varies from 7 V to 12 V. Assume that the load…
A: Brief description: In the above given question they want to know the design of zener diode regulator…
Q: A PMMC instrument has a coil of dimensions 17 mm x12 mm.The flux density in the air gap is 1.8 x10³…
A: In this question we need to find a number of turns in PMMC coil.
Q: 2. Determine the following for the network shown below: a. gm b. ZiAMP C. ZOAMP d. Given parameters:…
A:
Q: Q3: Find hybrid parameters for the network in fic 192 292 Figure 2 292 Figure 3 192 41₁1 1₂ 292 +
A: In this question, We need to determine the h parameters of the given system?
Q: Example 7.33. Two coils of inductances 4 and 6 henry are connected in parallel. If their mutual…
A: Given: Two coil of inductances 4 and 6 henry are connected in parallel, L1=4 H L2=6 H Mutual…
Q: Note: Answer Four Questions only Q1: A three-phase balanced source voltages, operating with a 380 -V…
A:
Q: In the circuit shown below power factor is
A:
Q: A balanced 3-phase, star connected load of 120 kW takes a leading current of 100A with a line…
A: Given, A balanced 3-phase star connected load with, Load power, PL=120 kW Leading current,…
Q: A light bulb has a 25 W rating, and it is plugged into a socket with terminals at a 220 V potential…
A: Current in light bulb is calculated as- power is given P=25W V=220volt
Q: 5. Find the input impedance at 20 krad/s for the circuit shown in Figure 4. 3mH 200 £2 m 0000 3v |…
A:
Q: The open circuit test in a 100 kVA, 2000/200 V, 50 Hz, single phase transformer gives 200 V, 90 A, 5…
A: Given, Power reading, P = 5 kW At low voltage side, V1=200 V Current reading, Io=90 A
Q: A 3 phase, 50 Hz, 434-V, supply is connected to a, Y-connected induction motor and synchronous…
A:
Q: ower plant has a capacity factor of 40.9% and a plant use factor of 45.2%. How many hours per year…
A: A power is a place where electrical power is produced to supply the demand of its customers.
Q: a coil of 10 ohms resistance and 0.1 H inductance is connected in parallel with a capacitor of…
A:
Q: 2i 0.5 Ω ΜΑ 120 ΜΗ Figure 6 20 μF
A: Brief description: In the above given question they have mentioned a parallel combination circuit…
Q: 2. Solve for I for the circuit shown in Figure 2, -j0.8 Ω 0.4Ω V Μ V2 | 16/450 νε 10.5Ω | 1 | 21…
A: In this questions, we need to calculate the current I. This current I can be obtained by applying…
Q: As a service engineer, you are troubleshooting at an electropneumatic system. You filled the…
A: PLC- Programmable Logic controller. It is an controller which works on the basis of implemented…
Q: Find I, & Iz₂ using 7010° mesh analysis. jio -j20 F2 I, 1514 40 190
A:
Q: Circuit Diagram V1 R1 220 Vrms >50 Ω 60 Hz 0.⁰ L1 100mH Computed Values Compute the expected power…
A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…
Q: A three-phase two winding transformer is rated 1200MVA, 24/345kV 50Hz. It has a leakage reactance of…
A: PU Kva = Actual KVA / Base KVA PU Voltage = Actual Voltage/ Base voltage In star connection, N1/N2…
Q: 5. As depicted in Figure 9.3, a 3-phase A connected generator feeds a Y connected load. The…
A: Given data, Line current VL=120V Vph=120V Impedance (Z) =5ohm
Q: What will be the length of a 10 ohm wire, when the resistivity of the wire is 0.1 ohms-m and…
A: Given: Resistance, R = 10 ohm Resistivity, ρ=0.1 Ω-m Diameter, d=0.5 m Radius, r = 0.25 m
Q: Find hybrid parameters for the I' network in figure ". ΤΩ 2Ω 2Ω ww ΤΩ •41 ΖΩ I, Ο +
A: In this question, We need to determine the hybrid parameters for the given network ? We are…
Q: A dc series motor drives a load a 30rev/s and takes a current of 10A when the supply voltage is…
A: In this question, We need to efficiency of the DC series motor? If input current I= 10A Supply…
Q: Consider the following circuit. Which of the following is the correct KVL equation? -60-30-Vx-40-0…
A: Given circuit,
Q: 2) A system has transfer function: Y(s) 50 R(s) S+50 Find the time constant, T, the settling time,…
A: In this question we will find time constant , settling time , rise time....
Q: Determine the value of the resistances based on band colors: A. Green, Blue, Black, Orange, Red B.…
A:
Q: A WLAN (wireless local area network) channel in the 60-GHz range is at 60.48 GHz. When propagating…
A: WLAN The method of wireless distribution for two or more device, it known as a wireless local area…
Q: +V₂ BB RB Rc [+Vcc
A:
Q: Visin30 Determine the output voltage for the circuit of Fig.3 blow. Where the *frequency is 10 KHz…
A: Operational Amplifier: Op-amps is a divided into noninverting and inverting amplifiers and it is…
Q: source entering to (2.) A 110 Vems bet the apparent the load 120 VA at a) complex power. 6.) RMS…
A:
Q: E7.17 The switch in the network in Fig. E7.17 moves from position 1 to position 2 at = 0. ANSWER:…
A:
Q: For the circiut shown, R = 600 Q, C = 4.0 µF, L = 3.0 H. Vm = 140 V and f = 100 Hz. The phase angle…
A: Given data, R=600 ΩC=4.0 μFL=3.0 HVm=140 Vf=100 Hz
Q: Exercise (2): 5 V; (E)( 32H TOIF Find View), and its poles and zeros. (W) Io (W) ij(t) 352
A: From circuit v0(s)/I(s) =Zeq
Q: Power will be consumed by the moto. it the blanks: 1. The two windings of a transformer is ...linked…
A:
Q: What is an autotransformer? What is the difference between autotransformer and a two winding…
A: Transformer- Transformer is a device by which one can regulate the input voltage. It is used to…
Q: Q1: A three-phase balanced source voltages, operating with a 380 -V line voltage as shown in Fig. 1.…
A:
Q: The two-wattmeter method produces wattmeter readings P2 = 800 W Wand P1= 560 W when connected to a…
A:
Q: j2 Ω m -jXcQ HE RQ ww 40/0° V ZL 5Ω or the circuit shown above, what is the magnitude of the load…
A:
Q: 22// Find the current at 10 2 by using hevenin's theorem? 292 192 10v +11+ 592 VIL 1092 H 20v
A:
Q: What is the minimum sum-of-products expression for the following Kmap?
A:
Q: Problem 04.002.c Identify the expression for the current through a 200-µF capacitor when vc (t)…
A: Given, Voltage across capacitor vct=28cos15t+π8 V Capacitance, C=200 μF
Q: Problem You are given the following Digital circuit. out CLK CLK D XO4x O CLK Xi out2 (Ctrl)- Doj…
A:
Q: 2. Discuss any two types of the lightning arresters.
A: The two types of lightning arrester are: Rod Gap Arrester This type of arrester is simple in…
Q: In a water heater, the power dissipated by the heating element is 1.8 kW when connected to a 120 V…
A: Given, Power dissipated, P=1.8 kW Supply voltage, Vs=120 V
Q: = The Thevenin impedance of a source is ZTh 89+ j 68, while the Thevenin voltage is VTh = 346 + j373…
A:
Q: The switch in Fig.4, has been in position a for a long time. At t-0, it moves to position -…
A:
Q: Q3: For the network in next Fig, determine the value of R for maximum power to R. R, 40 SA R$10 E24…
A:
.................................
Only 5 the rest are correct
...................................
Step by step
Solved in 2 steps with 2 images
- You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
- You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
- A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?A 22-k resistor and a 0.02-F capacitor are connected in series to a 5-V source. How long will it take the capacitor to charge to 3.4 V Select one: a. 0.501 ms b. 0.66 ms c. 0.44 ms d. 0.70 msWith V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
- 3. A resistor and a capacitor are connected in parallel across a 120 V DC source. Determine the voltages across the resistor and the capacitor.1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.An inductor of 230 milli Henry, a capacitor of 15 micro farad and a 200 ohm resistor are in series across a 36 V and 60 Hz voltage source. Find the total current a. 150 mA b. 0.164 A c. 0.2 A d. 170 mA