5) The center O of the spool starts from rest and acquires a velocity of 1.2 m/s up the incline with constant acceleration in a distance of s = 2.4 m under the action of a steady pull, P applied to point A of the cable. The cable is wrapped securely around the hub of the spool, and the spool rolls without slipping. For the s=2.4 m position shown, compute the acceleration of point A on the cable and point B on the spool. y B 250 mm 100mm0 s=2.4 m C 15° P

5) The center O of the spool starts from rest and acquires a velocity of 1.2 m/s up the incline with constant acceleration in a distance of s = 2.4 m under the action of a steady pull, P applied to point A of the cable. The cable is wrapped securely around the hub of the spool, and the spool rolls without slipping. For the s=2.4 m position shown, compute the acceleration of point A on the cable and point B on the spool. y B 250 mm 100mm0 s=2.4 m C 15° P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the pinion A of the hoist motor drives gear B, which is attached to the hoisting drum. The load L is lifted from its rest position and acquires an upward velocity of 4ft/sec in a vertical rise of 5 ft with constant accelerations. As the load passes the position, compute the acceleration of point 6 on the cable in contract with the drum.
Thex- and y-motions of guides A and B with right-angle slots control the curvilinear motion of the connecting pin P. which slides in both slots. For a short interval, the motions are governed by x= 25 +0.74t andy = 24 -0.42t. wherexand y are in millimeters and tis in seconds. Calculate the magnitudes of the velocity v and acceleration a of the pin for t = 1.75. Sketch the direction of the path and indicate its curvature for this instant. A Part 1 Incorrect Calculate thex- and y-components of the velocity. Answers: Vx= 1.48 mm/s -1.26 mm/s Vy= 1000000
An oil pumping rig is shown in the figure. The flexible pump rod D is fastened to the sector at E and is always vertical as it enters the fitting below D. The link AB causes the beam BCE to oscillate as the weighted crank OA revolves. If OA has a constant clockwise speed of 1.0 rev every 2.6 s, determine the acceleration ap (positive if up, negative if down) of the pump rod D when the beam and the crank OA are both in the horizontal position shown. 3.1 m- 3.44 m E 0.93 m 1.92 m 0.6 Answer: ap = m/s?
An oil pumping rig is shown in the figure. The flexible pump rod D is fastened to the sector at E and is always vertical as it enters the fitting below D. The link AB causes the beam BCE to oscillate as the weighted crank OA revolves. If OA has a constant clockwise speed of 1.0 rev every 3.7 s, determine the acceleration ap (positive if up, negative if down) of the pump rod D when the beam and the crank OA are both in the horizontal position shown. 3.2 m 3.25 m E 0.91 m 1.67 m 0.5 m Answer: ap = i 0.364 m/s2
The x- and y-motions of guides A and B with right- angle slots control the curvilinear motion of the con- necting pin P, which slides in both slots. For a short interval, the motions are governed by x = 20 + and y = 15 - , where x and y are in millimeters and t is in seconds. Calculate the magnitudes of the velocity v and acceleration a of the pin for t = 2 s. Sketch the direction of the path and indicate its cur- vature for this instant. B y A
At the instant shown, the AB bar is rotating counterclockwise with speed and acceleration angles shown in the figure. Determine the (linear) speed and acceleration of the sliding block C at that instant.
The x- and y-motions of guides A and B with right- angle slots control the curvilinear motion of the con- necting pin P, which slides in both slots. For a short interval, the motions are governed by x = 20 +t and y = 15 - , where x and y are in millimeters and t is in seconds. Calculate the magnitudes of the velocity v and acceleration a of the pin for t = 2 s. Sketch the direction of the path and indicate its cur- 4 vature for this instant. В P A
Write the vector expression for the acceleration a of the mass center G of the simple pendulum in both n-t and x-y coordinates for the instant when = 60° if = 2.00 rad/sec and 0 = 4.025 rad/sec². Answers: a = (i a = (i 4.0' in 8 en + i i+ i et) ft/sec² j) ft/sec²
A flywheel 6 ft in diameter accelerates from rest at a constant rate of 4 rpm per sec. Compute the normal and tangential components of the acceleration on the rim of the flywheel after 10 sec.
Magnetic tape is being fed over and around the light pulleys mounted in a computer. If the speed v of the tape is constant and if the magnitude of the acceleration of point A on the tape is 4/3 times that of point B, calculate the radius r of the smaller pulley.
The x- and y-motions of guides A and B with right- angle slots control the curvilinear motion of the con- necting pin P, which slides in both slots. For a short interval, the motions are governed by x 20 +t and y = 15 -, where x and y are in millimeters and t is in seconds. Calculate the magnitudes of the velocity v and acceleration a of the pin for t = 2 s. Sketch the direction of the path and indicate its cur- vature for this instant. В y A
Thex-and y-motions of guides A and B with right-angle slots control the curvilinear motion of the connecting pin P, which slides in both slots. For a short interval, the motions are governed by x = 20 + 0.46t? and y = 17 -0.74t3, wherex and y are in millimeters and tis in seconds. Calculate the magnitudes of the velocity v and acceleration a of the pin for t = 2.4 s. Sketch the direction of the path and indicate its curvature for this instant. B P Part 1 Calculate the x- and y-components of the velocity. Answers: Vx= i mm/s mm/s 1000000