5- For the following NPN BJT circuit, VBE=0.4V, RE=1.8K2, R1=200 K2, R2=50KN, Rc=1.5KN, and RL=2KQ. If the static load line is given in the graph and the operating point (Q-point) is marked, Answer the following: a) Which type of amplifier is this? b) From the given graph, obtain IB, Ic, VCE, and calculate B at the Q-point? c) Draw the equivalent circuit (AC analysis) d) Find the input and output impedances Zi & Zo and the voltage gain Av.

5- For the following NPN BJT circuit, VBE=0.4V, RE=1.8K2, R1=200 K2, R2=50KN, Rc=1.5KN, and RL=2KQ. If the static load line is given in the graph and the operating point (Q-point) is marked, Answer the following: a) Which type of amplifier is this? b) From the given graph, obtain IB, Ic, VCE, and calculate B at the Q-point? c) Draw the equivalent circuit (AC analysis) d) Find the input and output impedances Zi & Zo and the voltage gain Av.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Logic
QUESTION 5: A simplified class-AB output stage with BJTS is shown below. The circuit parameters are Vcc=15 V and R1 = 1900 2. For each transistor, Is= 9 x 10 ¬15 A. Determine the value of VBg that produces icn =ico=1 mA when vị= 0. What is the power dissipated in each transistor? Format : 2.7987275900068 VBB (V) Format : 62 Pon (mW)| (mW)| Format : 26 +Vcc icn VBB V BB 2 RL Qp lice -Vcc ww
Enclosed please find an amplifier circuit designed with a BJT transistor. VCC = 9Volt for the circuit. All capacity values are selected sufficiently large. BJT Transistor B = 100 Vbe(on) = 0.8V, VA=100V, Vt= 26mV Vce (sat) = 0.15Volt. Calculate “Vceq” and “Icq “ values at the operating point of the circuit. In what area does this BJT transistor work in? Draw the small signal equivalent circuit of the circuit. Calculate the AC small signal current earnings of the circuit (Ai = I out / I input). Note: Is the current passes over Rs source resistance and The IO current passes over RL source resistance. Please Calculate Rin input resistance?
Assignment Goal: You are to research for different methods of biasing BJT circuits, and to choose and describe one of these methods in details in order to design a single stage common emitter or common base amplifier circuit. The report should have the following sections and cover the points listed below: 1. An overview about the purpose of biasing, and different methods of biasing. 2. Design method of your own simple amplifier circuit. 3. Calculations and analysis (including all DC and ac analysis: operating point, current and voltage gains, input and output resistances, voltage waveforms at all nodes in the amplifier circuit..., etc). 4. Simulation results. (Use BC107 for the BJT in your simulation). 5. A comparison between calculated and simulated results, and a conclusion. Support your design and results with explanation and parametric studies in details. For example, in your designed circuit, vary the value of the collector resistance Rc to change the mode of operation of the…
(a) Using the hybrid-pi model with early voltage effect, compute the small signal voltage gain, Av, input resistance and output resistance for the CE BJT amplifier shown below. Q1. Vcc = 12 V B=100 VBE(ON) = 0.7V V = 100V R = 93.7k2 * R=6 k2 Vo Rs = 0.5 k2 C B E R,= 6.3 k2 Figure Q1(a)
Please show work
Question 1: For the Mosfet in the circuit shown below: VTp = - 0.8V, and Kp = 200 uA/V2. Find Vs and Vp. Where Kp = ½ kp'W/L. lo=0.4 m Vs R= 50 k2 Rp=S ka -5 V
3. Given the problem:
Consider the source follower circuit in Figure shown below, IQ = 10 mA VTP = -2 V, Kp = 5mA/V2, RL = 680 n, and 2 = 0.01 V-1. Where Kp=1/2 k'p(W/L). (i) What configuration is this circuit? Use T Model to Determine the small-signal voltage gain (V/Vi). (ii) (iii) What is the formula for Vo? (iv) What is the formula for Vi? Determine the small-signal voltage gain (VVi). (v) (vi) Find the output resistance Ro. V* =5 V 200 k2 V--5 V
Electrical Engineering Consider the emitter follower circuit below given Vcc=15V. VEE-15V, Rr. -1.8k, VBE 0.7V.VCE,aut = 0.2 V, and 8 = 100 for all the transistors. Find the value of resistor Rink? that will establish a blas current sufficiently large to allow the largest possible output voltage swing. Include the base currents for both Q₂ and Q₂. Please give your answer in two decimal places. Vcc 9 VEE VRE VER
For the amplifier network of figure below. given the following Rs= 0.5 kQ. Rg= 100 kN, Rc=5 k2. RE = 1 kQ. R=4kQ. Vcc=20 V, hje= 2 kQ. hfe =175, and ro=25 kQ. choose the correct values of the no load gain (AVNL). (AVL), and (AV5) from the following choices list: Vcc Rc RB 5 µF Rs wwHE 5 µF + RL V RE 10 µF
In the above circuit, BJT's VT values are not identical. a) For the collector currents of transistors to be 2 mA What should the R0 value be? b) Find the values for gm1 and gm2. c) Find the differential mode gain (ADM). d) Find the common mode gain (ACM). e) Find the CMRR value.