120Part 1 Semiconductor Devices and Basic Applications+10 V2.47 Consider the circuit shown in Figure P2.47. Assume each diode cut-in volt-age is Vy 0.6 V. (a) Determine R1, R2, and R3 such that Ipi = 0.2 mA,In2 = 0.3 mA, and Ip3 0.5 mA. (b) Find V, V2, and each diode currentfor R1 10 k2, R2 4 k2, and Ry 2.2 k2. (c) Repeat part (b) forR 3 k2, R2 6 k2, and R3 2.5 k2. (d) Repeat part (b) forR 6 k2, R2 3 k2, and R3 = 6 k2.The diede cut in t+5 Vin FigeR2is 0.7VDetermine the vanenmE het nZDzpartoftमामाफतीFigure P2.47+5 V+5 VIpi. D,

Answered: Image /qna-images/answer/d01d7ebc-1755-4d92-a2df-80e2e211f25d.jpg

47 Consider the circuit shown in Figure P2.47. Assume each diode cut-in volt- age is Vy 0.6 V. (a) Determine R1, R2, and R3 such that Ipi 0.2 mA, Ip2 = 0.3 mA, and Ip3 0.5 mA. (b) Find V, V2, and each diode current for R 10 kS2, R2 4 k2, and Ry 2.2 kS. (c) Repeat part (b) for R = 3 k. R, = 6 kO, and R = 2,5 k2. (d) Repeat part (b) for %3D %3D %3D %3D %3D

47 Consider the circuit shown in Figure P2.47. Assume each diode cut-in volt- age is Vy 0.6 V. (a) Determine R1, R2, and R3 such that Ipi 0.2 mA, Ip2 = 0.3 mA, and Ip3 0.5 mA. (b) Find V, V2, and each diode current for R 10 kS2, R2 4 k2, and Ry 2.2 kS. (c) Repeat part (b) for R = 3 k. R, = 6 kO, and R = 2,5 k2. (d) Repeat part (b) for %3D %3D %3D %3D %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

diode zener a, DESIGN THE NETWORK IN THE FIGURE, TO KEEP, "VL" at 12 V for a variation in load (IL) from 0 to 200 mA, DETERMINE "Rs" and "Vz" b. determine "P2min" for the Zener diode from section a
1- Explain briefly with figure if exist, the Degenerate semiconductors. 2- When a diode is connected in a Reverse Bias condition, the overall result is a small ne current. Why?
(1) Describe the behaviour of a p-n junction under forward and reverse biasing in terms of semiconductor behaviour and sketch the V-I Characteristics of a p-n Junction.
2.12 The full-wave rectifier circuit shown in Figure P2.12 has an input signal whose frequency is 60 Hz. The rms value of vs = 8.5 V. Assume each diode cut-in voltage is Vy = 0.7 V. (a) What is the maximum value of Vo? (b) If R = 102, determine the value of C such that the ripple voltage is no larger than 0.25 V. (c) What must be the PIV rating of each diode? R D2 Figure P2.12
2. Consider the below zener diode circuit and find the values of Ip1, Vp1, ID2, and Vp2. Use the constant voltage drop model which is shown is Figure 2. Show your solution steps clearly and explain them. The
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
Q2:- Find the level of Vo for each circuit shown in the Figure below. Also, determine the status of each diode; if it is forward or reverses biasing. Assume all diodes are silicone with 0.7v drop.
You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo 12 V to a 3 kQ load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t).
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo = 12 V to a 3 k2 load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t). Figure 1.d.
Q2) Explain the working of zener diode on both forward and reverse bias. From the circuit in the Figure-2, Rs=1KO, Vz=7.2V and RL=3KN. If Vs = 12V. Find out the following DC parameters: a) Is = ?, Current passing through resistor Rs b) IL = ?, Current passing through resistor RL c) Iz = ?, Current passing through Zener Diode d) VL= ?, Output Voltage (Figure-2) Rs 1k Ohm Is Iz RL VL Vs UA723_ZD2 .3k Ohm 12 V
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV