40 kg object is being pushed downwards at an angle of 32° with the horizontal. If the coefficient of static friction is 0.4 and dynamic friction 0.35. Determine (a) what must be the applied force P to overcome static friction and (b) what will be the required force P if the box is already moving. P 32° 40kg

40 kg object is being pushed downwards at an angle of 32° with the horizontal. If the coefficient of static friction is 0.4 and dynamic friction 0.35. Determine (a) what must be the applied force P to overcome static friction and (b) what will be the required force P if the box is already moving. P 32° 40kg

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.56P: The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The...

See similar textbooks

Similar questions

A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The coefficients of friction between the block ana the rail are us= 0.25 and uk= 0.20. Given: P2 = 200 N. P1 350 P2 Find the magnitude and direction of the smallest force P1 required to start the block moving up the rail. (You must provide an answer before moving on to the next part.) The magnitude and direction of the smallest force P1 required to start the block moving up the rail is °. N v (Click to select)
Two blocks with masses ma = P kg and mg = 100 kg are connected with a flexible cable that passes over a frictionless pulley as shown in Fig. The coefficient of friction between the blocks is 0.2. If motion of the blocks is impending, determine the coefficient of friction between block B and the inclined surface and the tension in the cable between the two %3D blocks. the force for P is 78kg A B 40°
A 6.00 kg block is pressed against a vertical wall by a force. The coefficient of static friction between the block and wall is 0.41 and the directional angle theta for the force is 48 degrees. Determine the magnitude of the force when the block is about to slide down the wall.
The 500KN block shown is in contact with a 45°incline. The w coefficient of friction is 0.25. Determine the horizontal force P necessary to 1.Just start the block up the 45° incline 2.Just to prevent the motion down the incline. 3.lf P=400KN, what is the amount and direction of friction force?