۱۰:۰۳ صdocs.google.com/forms10 نقاطFind the tension T in cords AB,* and BC, for equilibrium40° BA 60°1000NTAB= 453.2 N , TBC= 685.6 N OTAB= 500 N , TBC= 500 N OTAB= 507.7 N , TBC= 777.8 NTAB= 543.2 N , TBC= 685.6N O

As the three forces are non collinear and concurrent and system is in equilibrium, So we can apply…

Answered: 40° BA 60° |1000N TAB= 453.2 N , TBC=…

40° BA 60° |1000N TAB= 453.2 N , TBC= 685.6 N O TAB= 500 N, TBC= 500 N O TAB= 507.7 N , TBC= 777.8 N O TAB= 543.2 N , TBC= 685.6 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please I want a detailed explanation of the energy method rule placed in the first line and how these numbers appeared to us. I want a detailed explanation please urgent .
P1 + as 2g pg P2 +z, + hpompa.f L V² + z2 + h¢arbing +hx,toplam_hxsûrekli= f. pg 'D´2g Wmil hỵ̟toplam= hx,sûrekli + hx,yerel Nsp = (gH)³/4 hkyerel = 2g Протра 一()-)图)第-(=)G) 5 HB Wmil,B _ PB (WB PAlwa) DA Wmil,A WR (DB wWm/2 Ns = %3D WA (DA HA Wmil = PgHỳntarbin p1/2(gH)5/4 Wmil = prwv(V; – rw)(1 – cosß) At the best efficiency point with the experiments on the A turbine DA= 72 cm, HA= 20 m, V = 50 m/s, PA= 998 kg/m³, na= 205 revolution per minute , Wmila= 9 MW values have been obtained. PB= 998 kg/m³, HB= 65 m, nâ= 185 A new B turbine will be designed. According to this ; a) B is the volumetric flow of the turbine (VR) (m/s) find as. c) Find the specific speed of turbine B. b) Find the power of turbine B. (Wmil.B) 2.5 d) Find the diameter of turbine B. 285 245.3 MW 3,5 120 cm 361 211,5 MW O 2.8 156 cm 180 190 MW O 2,1 144 cm 255 182,7 MW O 31 O 104 cm 375 250 MW O 95 am O O
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
Velocity analysis of Scotch Yoke Mechanism To determine the velocity of slotted slider for different crank lengths at different crank angles for various angular velocity
Mechanical Engineering xyz= 703 Stress, ksi (log) 72 49 35 28 10³ 8 x 10³1 10¹ 401 X 8't 49 ksi 10 ksi 401 X 9'1 35 ksi 28 ksi 105 Cycles (log) 106 19.8 The provided S-N curve shows the fatigue strength of a ferrous component with unknown geometry. 107 Given the following duty record, how much life is consumed at each stress level? 60 ksi 500 cycles 2000 cycles (600 000 + XYZ*100) cycles (15000 + XYZ) cycles 40000 cycles
6:05 Gmail > صباحي 3.JPG 120 N 80 N 150 N 30° 40° 35° Fig D2 22
2X° Cos 5y dx + x tan5y dy = 0 %3D
explain me the whole process do integration for each step properly
1- This equation ((mx+ kx = 0)) called equation of motion in. %3D a) Free vibration b) Forced vibration c) Natural frequency d) Damping force 2- The equation ((mx + kx = F sin wt)) called equation of motion in. a) Free vibration b) Forced vibration without damping c) Natural frequency d) Damping force 3- In this equation the second part represent , Folk x(t) = A,coswnt + A2sinwnt + (- )sinwt a) Transient solution b) Complete solution c) Free vibration d) Steady state solution
using equation 1 solve equations 2 and 3, show me in detail how to get the value solving equaion. how to use equation 1 to solve equations 2 and 3.
Express each of the following in the form ? + ??. *Complete Solution
Figure 1.3. Shows a preheater for a diesel engine that allows the engine to get hot air to facilitate combustion on a cold start. It consists of an insulated and sealed cast Iron chamber in the engine block with a volume of 0.25m³ at an initial pressure of 1.5 Bar. The Initial temperature is 50 degrees Celsius. A heating element of 50 Watts is to be applied to the chamber for 0.5 minutes prior to the engine start. (i) What type of process occurs in the preparation for engine start. (ii) Determine the final temperature in the chamber just prior to starting the engine. (iii) Determine the final pressure inside the chamber just prior to starting the engine.