4. The gate shown is hinged at O contains water on one side and oil on the other. What force F is required to hold the gate vertical? The width of the gate is 0.7 m. Also determine the reaction at the hinge. * Water Hinge. Net force is less than 7kN and hinge reaction is less than 5kN Net force is greater than 10KN and hinge reaction is greater than 7kN Net force is greater than 15KN and hinge reaction is less than 6kN 3.5 m 2.8 m 2.2 m

4. The gate shown is hinged at O contains water on one side and oil on the other. What force F is required to hold the gate vertical? The width of the gate is 0.7 m. Also determine the reaction at the hinge. * Water Hinge. Net force is less than 7kN and hinge reaction is less than 5kN Net force is greater than 10KN and hinge reaction is greater than 7kN Net force is greater than 15KN and hinge reaction is less than 6kN 3.5 m 2.8 m 2.2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 3 The aluminum rod BC (G = 26 GPa) is bonded to the brass rod AB (G = 39 GPa). Knowing that each rod is solid and has a diameter of 12 mm, determine the angle of twist (a) at B, (b) at C. 200 mm Brass - Aluminum 300 mm C 100 N. m
A steel plate is used to connect a column and beam as shown in Fig. 3. The connection betweenthe beam and the plate is fillet welds. Given Q=150kN and Mx= -5kN-m (applied at centriod ofthe welds between the beam and the plate), determine maximum shear stress in the welds betweenthe beam and the plate.
Show FBD and complete solutiondetermine the reactions of the cantilever beam
Steel A-450 mm² E-200 GPa L-4.0 m A B opper A=230 mm² E-120 GPa L= 3.0 m 5.0 m a) What maximum P can be applied on the horizontal bar to give a stress of 110 MPa to steel and 150 MPa to copper. How far from copper should P be acting. Neglect the weight of the bar. b) What are the amount of deformations of the rods
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.
Q1: A torque T = 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa. Determine: (a) maximum shearing stress in the in the steel core. (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A. 172 mm 54 mm- A Steel core- 25 m Aluminum Q2: aluminum rod AB (G=27GPa) brass rod BD (G= 39GPa). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram 60 mm TB 1600 Nm 36 mm T₁ = 800 Nm. 400 mm q+ 375 mm 250 mm
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
The brass rod AB is fixed connected at A. When the temperature is T₁-50 °C, there is a 3 mm gap between its end (point B) and the wall C. The cross-sectional area of the rod is 10 cm². Ignore the weight of the bar. The temperature is now increased to T₂-130 °C and the rod AB is pushing against the wall at C. Ebr = 100 GPa, abr = 20 x 10-6/°C Fallow 70 MPa L = 3m A 3 m B/C с 3 mm a. Draw a FBD for when the temperature is increased to T₂ and write down the force balance for this scenario. Call the reactions at FA and FC. Ton =1) und prit brolim volgen Aistis Intelesa si s b. State the compatibility condition and solve for the reactions at A and C.
Find the EIδ under 200lb load EIδδ under 400lb load
o Given: A stepped shaft with the following properties Copper: A = 2 in² E = 16 × 106 psi Steel: A = 1 in² E = 30 × 106 psi copper 12" steel 12" P steel 12" copper 6" → P HA o Find: P such that the deformation, A is 0.1 in at the end of the bar.
fotografları görüntale + Şuraya ekle: % Düzenle ve Oluştur v 2 Paylas The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. The diameter of the pin is d = 11.4 mm. (Figure 1) Part A Determine the maximum bending stress on the cross-sectional area at the center section a-a. For the solution it is first necessary to determine the load intensities w, and u2 Express your answer to three significant figures and include the appropriate units. ? Value Units Omax = Submit Reguest Answer Figure 1 of 1 > < Return to Assignment Provide Feedback 3600 N ti 25 mm 25 mm 40 mm 1800 N 1800 N
€ = - 20 N/nn Compute the displacements of the plate wing single quad ekmeent a 2 m I(0,1) 4 (2, 1) 0.5 m Im 3(2,0.5) E = 3(10*) Pa V = 0.3 2 (0,0) thickness Im %3D