4. Ina consolidated drained tri-axial text on a normally consolidated clay soil a deviator stress of 152 kPa was required to fail the sample when the confining pressure was 70 kPa. a. What was the angle of shearing resistance ? b. Suppose that after consolidation under the 70 KPa confining pressure, the sample is placed in an unconfined compression apparatus and tested. Determine the resulting shear strength.

4. Ina consolidated drained tri-axial text on a normally consolidated clay soil a deviator stress of 152 kPa was required to fail the sample when the confining pressure was 70 kPa. a. What was the angle of shearing resistance ? b. Suppose that after consolidation under the 70 KPa confining pressure, the sample is placed in an unconfined compression apparatus and tested. Determine the resulting shear strength.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.7P

See similar textbooks

Similar questions

Answer any one asap 1.A triaxial test is performed on a normally consolidated clay. The sample is further consolidated by the test of all-around confining pressure prior to the application of the axial load. The axial force is applied very slowly. The equipment pore pressure lines remain open so that drainage of the soil pore water can occur during the test. The sample fails when minor principal stress is 49 kPa and the major principal stress is 91 kPa. Determine the angle of internal friction with no decimal places. 2.A dry sand sample was tested in direct shear and yielded a shear strength of 132 kPa under a normal stress of 215 kPa. Lab results indicate the soil's wet unit weight is 18.1 kN/m3 and the saturated unit weight is 20.2 kN/m3. Determine the shear strength, in kPa, within the native sand deposit at a depth of 2.5 m below the water table. The water table is 3 m below ground surface. Provide your answer with 2 decimal places, do not include the units and assume a unit…
Please give me right solution according to the question. In a triaxial test on a saturated clay, the sample was consolidated under a cell pressure of 160 kPa. After consolidation the cell pressure was increased to 350 kPa, and the sample was then failed under undrained condition. If the shear strength parameters of the soil are c’ = 15.2 kPa, ϕ’ = 26°, B = 1, Af = 0.27, determine the pore pressure at the failure.
A direct shear test was conducted on a dried sand sample in a test box of 60mm x 60mm normal load of 400N. The soil sample failed at an applied shear force of 250N. a. Determine the shear strength parameters of the soil. b. Estimate the required shear force to cause a shear failure under a normal load of 600N. (Show all working calculations.)
5. A consolidated, undrained triaxial test is being carried out on a normally consolidated clay where c - 0 and p'= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?
5. A consolidated, undrained triaxial test is being caried out on a normally consolidated clay where c = 0 and 41= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?
Three specimnens of clay having a small air-void content were tested in the shear box. Shear loading was started immediately after the application of the normal load and was completed in 8 minutes. The results are as follows: Normal Stress (kN/m2) Shear stress at failure (kN/m2) O Find the apparent cohesion of the clay. Find the angle of shearing resistance of the clay. What value of c would be obtained from an unconfined compression test on 145 241 337 103 117 131 the same soil?
A CU triaxial test was carried out on a silty clay that was isotopically consolidated using a cell pressure of 125 kPa. The following data were obtained: Axial load (kPa) 0 5.5 11.0 24.5 28.5 35.0 50.5 85.0 105.0 120.8 Axial strain, &₁ (%) 0 0.05 0.12 0.29 0.38 0.56 1.08 2.43 4.02 9.15 Au (kPa) 0 4.0 8.6 19.1 29.3 34.8 41.0 49.7 55.8 59.0 (a) Plot the deviatoric stress vs. axial strain and excess porewater pressure vs. axial strain, respectively. (b) Determine the undrained shear strength (sµ). (Note: we assume that the sample reaches failure). (c) Determine the total principal stresses (0₁,03) and the effective principal stresses (0₁, 03') at the failure, respectively.
c. An undisturbed soil sample, 110 mm in diameter and 220 mm in height, was tested in a triaxial machine. The sample sheared under an additional axial load of 3.35 kN with a vertical deformation of 21 mm. The failure plane was inclined at 50° to the horizontal and the cell pressure was 300 kN/m². i. Draw the Mohr circle diagram representing the above stress conditions, and from it determine: - Coulomb's equation for the shear strength of the soil, in terms of total stress; - the magnitude and obliquity of the resultant stress on the failure plane. ii. A further undisturbed sample of the soil was tested in a shear box under the same drainage conditions as used for the previous test. If the area of the box was 3600 mm² and the normal load was 500 N, what would you expect the failure stress to have been?
Question 2 The result presented in Table Q2a were obtained from a consolidated drained (CD) triaxial test on a normally consolidated clay sample of 75mm height x 38mm diameter tested at a confining pressure of 50 kPa. Table Q2a. CD triaxial test result Axial strain (%) 1 2 5 10 15 Applied force (kN) 0.01 0.03 0.05 0.08 0.10 Page 3 of 6 (a) Draw the Mohr circle for each stress state in the sample and the total stress path (TSP) throughout the test and determine the slope of the TSP to the horizontal.
The water content of a sample of saturated soil at a mean effective stress of 10 kPa is 85%. The sample was isotropically consolidated with a mean effective stress of 150 kPa. At the end of the consolidation, the water content was 50%. The sample was then isotropically unloaded to a mean effective stress of 100 kPa, and the water content increased by 1%. Given: Gs = 2.7, o'cs = 25°. a) Calculate and K. 10 b) Determine the failure stresses (p'f and gf) under CU test and CD test for the conditions.
Import your data for FREE Buy now c. An undisturbed soil sample, 110 mm in diameter and 220 mm in height, was tested in a triaxial machine. The sample sheared under an additional axial load of 3.35 kN with a vertical deformation of 21 mm. The failure plane was inclined at 50° to the horizontal and the cell pressure was 300 kN/m². Draw the Mohr circle diagram representing the above stress conditions, and from it determine: Coulomb's equation for the shear strength of the soil, in terms of total stress; the magnitude and obliquity of the resultant stress on the failure plane. ii. A further undisturbed sample of the soil was tested in a shear box under the same drainage conditions as used for the previous test. If the area of the box was 3600 mm² and the normal load was 500 N, what would you expect the failure stress to have been? Q Search IN 9 quickbooks N quickbooks in reports 9:52 an 29/04/202
A consolidated-undrained tri-axial test was conducted on a normally conslidated clay sample and the results are follows: Chamber confining pressure= 119kpa Deviator Stress at failure=90 kpa Pore water pressure= 58kpa These results were used to determine the drained friction angle of the soil. Compute the deviator stress (kpa) at failure when the drained test was conducted with the chamber confining pressure changed to 156 kpa. Use stored value. Answer to 5 decimal places.