4. An ideal double reheat steam turbine receives 300,000 kg/h of steam at 10 MPa and 400°C. After expansion from high pressure shell, it is reheated twice from saturated vapor condition back to its initial temperature. The steam entering the condenser is 97% dry. Determine: (A) Engine work (B) Engine thermal efficiency

4. An ideal double reheat steam turbine receives 300,000 kg/h of steam at 10 MPa and 400°C. After expansion from high pressure shell, it is reheated twice from saturated vapor condition back to its initial temperature. The steam entering the condenser is 97% dry. Determine: (A) Engine work (B) Engine thermal efficiency

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

STEAM IS DELIVERED TO AN ENGINE AT 5 MPa and 600°C. BEFORE CONDENSATION AT 30°C. STEAM IS EXTRACTED FOR FEEDWATER HEATING 0.60 MPa. FOR AN IDEAL CYCLE, FIND (A) THE AMOUNT OF STEAM EXTRACTED. (B) WORK (C) THERMINAL EFFICIENCY . FOR AN IDEAL ENGINE AND SAME STATES, COMPUTE. (D) WORK AND THERMINAL EFFICIENCY (E) STEAM RATE.
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 9. Calculate the total pump work of the cycle
(a) Identify the effectiveness of a regenerator and demonstrate why the enthalpy value before the turbine expansion process is important.
A 1000-MW supercritical double-reheat steam power plant operates withthe main (live) steam condition of 250 bars and 560°C and the condenserpressure of 0.04 bar. The steam is reheated first at 30 bars to 560°C andthen at 4 bars to 560°C. The turbine efficiency is 0.92. The feed pumpwork may be ignored. Calculate: (a) the plant net specific work, (b) the plant thermal efficiency, (c) the plant steam mass flow rate, and (d) the plant heat rate.
Consider a steam plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa and 350°C and is condensed in the condenser at a pressure of 10 kPa. Determine The thermal efficiency if steam is superheated to 600°C instead of 350°C in %. Include your T - S diagram on your solution SI unit plsss thankyou
Unit No. 6 at The Geysers produces 52 MW of power at the generator from a steam flow of 417,000 kg/h at a pressure of 6.9 bar and a temperature of 182°C. The reservoir conditions are known to be 32.3082754 bar and 238°C. The turbine exhaust pressure 2. (condenser pressure) is 0.13 bar. (a) Sketch the location of the reservoir and turbine-inlet state points on the attached Mollier chart (h-s). The requested states should be placed on this h-s diagram. What do you observe about the enthalpy of these two states? What do you notice about these values relative to the maximum enthalpy along the saturated vapor line? (b) On the same diagram, locate the turbine exhaust state. Calculate the turbine isentropic expansion efficiency, 71. Calculate the overall geothermal energy utilization efficiency, 7u, based on (i) reservoir and (ii) turbine-inlet conditions. A sink temperature of 48°C is appropriate for Unit No. 6.
TNB steam power plant in Genting Highlandsoperates on reheat Rankine cycleand has power net output of 50MW. Steam enters the turbine at aMPa and b °Cand it is cooled in the condenser at a pressure of ckPa by running cooling water from the Bertam River through the tubesof condenser. Steam enters both stages of the turbine at b°C. If the moisture content of the steam at the exit of the low-pressure turbine is not to exceed 10 percent, show the cycle on a T-s diagram and determine;i.The pressure at which reheating takes place, ii.The thermal efficiency of the cycleandiii.Please justify how does the thermal efficiency of the cycle if the temperature to low turbine is increase to 600°C? a=12 b=500 c=12
A four-cylinder, 8 cm x 10 cm, single acting, V-type compressor operates at 600 rpm. Iti s used in a Freon-12 vapor compression system with condenser and evaporatort emperatures of 29OC and -14OC, respectively. If the compression is dry and isentropic,the clearance is 2 percent. (a) Draw the cycle schematic diagram and (b) draw the corresponding p-h diagram and determine (c) the refrigerating capacity in tons, (d) the heat given off in the condenser, and (e) the COP. The gas constant, k for R-12 is 1.126.
Problem (5.5) Superheated water vapor enters the turbine at 5Mpa and 400 °C. The water leaves the condenser as saturated liquid at a pressure of 30kPa, and the turbine efficiency is 91%. The net power output of the cycle is 100MW. Determine: a- The thermal efficiency, b- Mass flow rate of steam in the cycle
An r-134a refrigerator operates a simple vapor compression cycle (SVCC). The evaporatoroperates at -10 °C, while the condenser operates at 1 MPa. R-134a flows around the system at 10 g/s.a. Graph the cycle in a P-h diagram and calculate the temperature at the exit of the compressor, assuming it is 100% isentropicallyefficient.b. Calculate the power required by the compressor (in W) and the cooling effect of the refrigerator (in kW) c. Compute for the COP of the system. What is its percent difference from the reversible efficiency?
A gas turbine power plant operates on a simple thermodynamic cycle. The ambient conditionsare 100 kPa and 24 °C. The air at this condition enters the engine at 150 m/s whose diameteris 0.5 m. The pressure ratio across the compressor is 18 k and the temperature at the turbineinlet is 1400 K. Assuming ideal operation for all components and specific heats for air andproducts separately. In addition, neglect the mass of fuel burned. Do the followings:a. Choose the suitable thermodynamic cycleb.Draw pv and Ts diagram and label itCalculate the power required by the compressordDetermine the pressure and the temperature at the turbine exit,Compute the power produced by the turbinef.Available specific workg.The thermal efficiency
Q5/ A boiler is capable of generating 8 kg steam per kg of fuel at 400°C. Feed water is supplied at pressure of 30 bar, 40°C and leaves economizer at 150 °C for entering to evaporator. Steam leaves evaporator with dryness fraction of 0.98 and enters the superheater. Fuel used has calorific value of 29000 kJ/kg. Considering no pressure loss inside the boiler determine boiler efficiency and fraction of heat given to steam in each section of boiler. Boiler efficiency = 84.52% % fraction of heat in economiser, evaporator and superheater = 15.01%, 69.89% and 15.1%