4. A concrete gravity dam is shown in the figure below. The depth of water at the upstream side is 6m. Use the unit weight of concrete =23.50kN/cU.m. Determine the following: a. vertical reaction b. Factor of safety against sliding. Use coefficient of friction=D0.60 c. Factor of safety against overturning 2m 8m 6m 4m

4. A concrete gravity dam is shown in the figure below. The depth of water at the upstream side is 6m. Use the unit weight of concrete =23.50kN/cU.m. Determine the following: a. vertical reaction b. Factor of safety against sliding. Use coefficient of friction=D0.60 c. Factor of safety against overturning 2m 8m 6m 4m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The section of a gravity is as shown in the figure. Assume hydrostatic uplift to vary uniformly from full hydrostatic uplift from heel to zero at the toe. Determine the total reaction per unit length at the base of the dam (lbs/foot). Use sp. gr. of concrete = 2.4. x = 19.1 ft.
NOTE!! ONLY ANSWER D, E, AND F. THANK YOU. A section of a gravity masonry dam is shown in the figure water is flush at the top of the dam upstream and 5m from the ground downstream. Assume hydrostatic uplift to vary uniformly from full hydrostatic pressure from the heel to zero at the drain density of water is 1000kg/m^3. The specific gravity of concrete is 2.4. Determine: a. The location of the resultant force b. Factor of safety against sliding if coefficient of friction is 0.75 c. Factor of safety against overturning d. Stress at the heel and the toe e. Unit horizontal shearing stress at the base f. Factor of safety against overturning neglecting uplift NOTEEE!!! (Only answer D, E, and F)
Situation 1 - A small dam of height h = 2.2 m is constructed of vertical wood beams of thickness t = 120 mm, as shown in Figure S01-0321. Consider the beams to be simply supported at the top and bottom. Assuming that the weight density of water is 9.81 kN/m³. m 2.1 17. Determine the maximum shearing stress in the beam in MPa. A. 0.198 C. 0.147 B. 0.256 D. 0.321 18. Determine the maximum bending stress in the beam in MPa. A. 3.214 C. 2.792 B. 2.248 D. 2.587 TE h B Figure S01-0321
A section of a gravity masonry dam is shown in the figure water is flush at the top of the dam upstream and 5m from the ground downstream. Assume hydrostatic uplift to vary uniformly from full hydrostatic pressure from the heel to zero at the drain density of water is 1000kg/m^3. The specific gravity of concrete is 2.4. Determine: a. The location of the resultant force b. Factor of safety against sliding if coefficient of friction is 0.75 c. Factor of safety against overturning d. Stress at the heel and the toe e. Unit horizontal shearing stress at the base f. Factor of safety against overturning neglecting uplift
2. The tank shown below has an irregular shape. Determine the following: a) The magnitude and the direction of the horizontal force. (Ans. Fx=22,500 Ib) b) The magnitude and the direction of the vertical force. (Ans. F,=19,900 Ib) Assume the width of section AB is 4 ft (into the page). Water Tank- wall 18 ft 6 ft B
A concrete, gravity dam has the following cross section properties as given in the figure below. The uplift pressure at the base of the dam varies linearly from 60% hydrostatic pressure at heel to zero at toe. Specific gravity of concrete is 2.4 a. Calculate the factor of safety against sliding. Use u = 0.6. b. Calculate the factor of safety against overturning. c. Solve for the location of the resultant force from the toe d. Calculate the maximum soil pressure developed at the base of the dam. e. Calculate the minimum soil pressure developed at the base of the dam. 2.6 m 8. 21.6 m 18.6 m 12 m
The height of the reinforced concrete water dam in the figure is L width a. The unit weight of the body of the dam Su gola Betogarme su bendi is y=24 kN/m'. Since the height of the water lake is h and the lateral water thrust to the body is H=5h? kN/m, determine the maximum water height (hmax) to avoid 4. tensile stress at the base of the dam. (L=15m, a=7m) Note: Calculate for unit height (taking 1 m),
Problem Refer to the figure shown. Determine the following considering the effect of the Prestressing force and Working loads simultaneously. 12 kN/m Section: 10 kN/m С.G. 750 mm 200 mm A 8 m 7 m 350 mm a. Determine the ftop at x=8 m from left end. (MPа). b. Determine the fbot at x=8 m from left end (MPа).
2. Figure 2 shows a 0.8 m wide of rectangular sluice gate is hinged at point A on the wall of a reservoir, which is inclined at 30° to the vertical. The vertical distance between the water surface to the point A is 8 m. Solve, The resultant force and its centre of pressure vertically from the water surface to the rectangular sluice a. gate. b. The distance, h along the wall surface to the location of resultant force as shown in Figure 2. Water level 8 m 30 Figure 2
Figure shown below is a gate in the form of circular arc with a central angle of 60° and radius 2m with one end resting on the crest of the dam. The water surface is flushed with the upper end of the gate. Find the vertical component of hydrostatic force (kN) acting on the gate. The gate is 2.22 m long normal to the plane of the paper. O 2m 60 ° 2m
The crest gate shown consists of a cylindrical surface which AB is the base, supported by a structural frame hinged at C. It is retaining water on one side. The length of the gate perpendicular to the paper is 5.9 m. Use R = 6 meters, and e = 52° Determine the distance (in meters) of the vertical component of the hydrostatic force measured from the hinge at C. Round off to three decimal places. W.S. HINGED R
A crest gate shown in Figure 1. consists of a cylindrical surface of which AB is the base, supported by a structural frame hinged at C. The length of the gate perpendicular to the paper is 10 m. a. Compute the vertical force component of hydrostatic force. b. Compute the horizontal force component of hydrostatic force. c. Obtain the location (from point C) of the vertical component of the hydrostatic force. Figure 1 A B 6.m 60⁰ C