4) Write an assembly program that turns on the LED as soon as BTNO is pressed and turns it off as soon as it is released. The program must also use TIMERO timer to measure the duration of pressing the button and print this duration in milliseconds in the terminal window upon the button release. The program must be capable to measure the duration up to 100 seconds. Make sure to process GPIO and TIMERO hardware interrupts by using interrupt handlers and NVIC, so no flags polling.

4) Write an assembly program that turns on the LED as soon as BTNO is pressed and turns it off as soon as it is released. The program must also use TIMERO timer to measure the duration of pressing the button and print this duration in milliseconds in the terminal window upon the button release. The program must be capable to measure the duration up to 100 seconds. Make sure to process GPIO and TIMERO hardware interrupts by using interrupt handlers and NVIC, so no flags polling.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

When do you need to use the word "Interrupt?" Is it conceivable, by listing the many kinds of hardware interruptions, to explain why none are anticipated?
The processor will put a halt to whatever it is doing when it detects a signal so that it can reply to the request. The following is the technique that was employed to deal with this situation: A "Signal of Interrupt Spooling" B "Handling of Interruptions" C "Interrupt Spooling" D Polling.
Suppose that you are designing a game system that responds to players' pressing buttonsand toggling joysticks. The prototype system is failing to react in time to these input events,causing noticeable annoyance to the gamers. You have calculated that you need to improveoverall system performance by 50%. This is to say that the entire system needs to be 50%faster than it is now. You know that these I/O events account for 75% of the systemworkload. You figure that a new I/O interface card should do the trick. If the system'sexisting I/O card runs at 10 kHz (pulses per second), what is the speed of the I/O card thatyou need to order from the supplier? Suppose the daytime processing load consists of 60% CPU activity and 40% disk activity.Your customers are complaining that the system is slow. After doing some research, youhave learned that you can upgrade your disks for $8,000 to make them 2.5 times as fast asthey are currently. You have also learned that you can upgrade your CPU to make…
please type so that i can read your solution
On a computer, what does the abbreviated form of the interrupt service process look like?
Develop a PIC18F4321 Interrupt based program to measure the power in watt absorbed by a resistor R2 = 60 resistor and input voltage Vs = 5V when the switch S1 is closed in the below figure. Write a C-code to configure INTO to trigger the Interrupt and use the ISR to calculate the power. + IT Vs T IT TO PIC S1 IR2 IR1 R2 R1
Create a PSOC interrupt driven program that performs the following: • Flashes an LED on and off using an 8-bit timer component • Assume a counter period of 200 • Assume a frequency of 900 Hz • The LED is turned on/off in the interrupt Provide screenshots of the pins, component layout, and component settings. You do not have to implement the hardware, e.g. connect an LED – just write the software
The interrupt vector table at the kernel's entry point stores what information exactly?
Number 3 please
An ADC produces an interrupt request and the interrupt service routine runs and acquires a burst of data of 10 data values into a global array. What is a good way for the ISR to tell the main program there is new data in the array? Set a global flag variable. Do nothing. The main program has to check if the data array has changed. Pass the array as a return value from the ISR. Clear the interrupt flag in the ADC.
After quickly going through the different interrupt types, you can use an example to drive home just how important they are to the machine's functioning.
Define a new interrupt (Interrupt number 80H). The interrupt service routine for this interrupt will ask the user to enter 2 numbers A and B(each is between 0 and 9), then it will print one of the following statements: - "A > B" - "A < B" - "A = B" TASM