4 in.200 kip3 ft- The column is constructed from high-strength concrete and eight A992 steel reinforcing rods.If the column is subjected to an axial force of 200 kip, determine the average normal stress in theconcrete and in each rod. Each rod has a diameter of 1 in- change the applied force of 200 kip to 185.7 kip- change original diameter of each steel rod of 1 in to 1.35 in

Answered: Image /qna-images/answer/0da8f95f-805f-419c-aa6f-c4bddef68897.jpg

4 in. 200 kip 3 ft The column is constructed from high-strength concrete and eight A992 steel reinforcing the column is subjected to an axial force of 200 kip, determine the average normal stress ncrete and in each rod. Each rod has a diameter of 1 in change the applied force of 200 kip to 185.7 kip change original diameter of each steel rod of 1 in to 1.35 in

4 in. 200 kip 3 ft The column is constructed from high-strength concrete and eight A992 steel reinforcing the column is subjected to an axial force of 200 kip, determine the average normal stress ncrete and in each rod. Each rod has a diameter of 1 in change the applied force of 200 kip to 185.7 kip change original diameter of each steel rod of 1 in to 1.35 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STRENGTH OF MATERIALS The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for steel is 360MPa, determine the minimum thickness t of the pipe if it supports the force of 600KN. Use a factor of safety against failure of 1.50. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.50. The failure bearing stress for concrete is 28MPa.
An extruded aluminum beam has the cross section shown. Knowing that the vertical shear in the beam is 10 kips, determine the shearing stress at (a) point a, (b) point b. 2.4 in. 0.5 in. 0.25 in. 0.25 in. 4 in. a -0.5 in. t 1.2 in. 4
PROBLEM 3 1.8 Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (w) are shown in the figure. Steel: A=500 mm² -120 MPa Timber: 4P A-2000 mm² = 12 MPa Concrete: A = 8000 mm² 0-16 MPa FIG. P1.8
ASAP dont round off initial values, round off final ans only
The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm Eal = 70 GPa. |800 kN/m +100 mm -100 mm A B 125 mm I800 kN/m Answer: 0A = 0c = 189 MPa, oB 21.4 MPа
Hand written please
An axial load P is supported by a short steel column, which has a cross-sectional area of 10500 mm2. If the average normal stress in the steel column must not exceed 140 MPa, determine the minimum required dimension “a” so that the bearing stress between the base plate and the concrete slab does not exceed 11 MPa.
The concrete column is reinforced using four steelreinforcing rods, each having a diameter of 25 mm.Determine the stress in the concrete and the steel if thecolumn is subjected to an axialload of 1200 kN. Est = 200 GPa,Ec = 25 GPa.
Determine the maximum flexural stress in the beam loaded as shown below
The allowable shear stress is τallow=895 psi�allow=895 psi. The supports at A� and B� are smooth
Allowable Compressive Stress A structural column Z section having a length of 10 m has an area of 600mm^2, Ix= 120x10^6 mm^4, Iy= 50x10 6 mm^4 and Ixy- -75x10^6 mm^5, Fy - 250 MPa. a) Determine the minimum moment of inertia. b) Determine the maximum moment of inertia. c) Determine the allowable axial stress. d) Determine the factor of safety. .....
(32 H.W Find longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal pressure. is 0.9 MPa and thickness of Wall is 6.4mm ? Ans: 6 = 42.19 MP₂ °H = 62.8 Mra 4 Also find I ?=0.67 Alir G 0.6m fot TE L = 1.8m O 7 0.6m