4) Based on the circuit to the rightSwitch s closed forSHOW ALL WORKSTEADY STATE20uF12V12k0R2(b)/(C)(d) The current lowing through Resistor R3 and the charge on the platesof capacitor C2 is (NOTE: This problem is worth triple points)(0)50 mA, 10jC m) 15 mA 24 C () 10 mA 200(ov)45mA 172 pC

solution of above question given in below step.

4) Based on the circuit to the right answer the folowing questions. SHOW ALL WORK Swilch is closed for long time, capacilors are fully charged, no current flows through the capcitors STEADY STATE 20uF - 12V SuF 3kD C1 RT 12kO R2 4kO R3 (b) /(C)/(d) The current flowing through Resistor R3 and the charge on the plates of capacitor C2 is (NOTE: This problem is worth triple points)

4) Based on the circuit to the right answer the folowing questions. SHOW ALL WORK Swilch is closed for long time, capacilors are fully charged, no current flows through the capcitors STEADY STATE 20uF - 12V SuF 3kD C1 RT 12kO R2 4kO R3 (b) /(C)/(d) The current flowing through Resistor R3 and the charge on the plates of capacitor C2 is (NOTE: This problem is worth triple points)

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 30CQ: Regarding the units involved in the relationship t = RC, verify that the units of resistance times...

See similar textbooks

Similar questions

In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
Consider the circuit in Figure 21.29 and assume the batter has no internal resistance. (i) Just after the switch is closed, what is the current in the battery? (a) 0 (b) /2R (c) 2/R (d) /R (e) impossible to determine (ii) After a very long time, what is the current in the battery? Choose from the same choices.
(a) Find the current in each resistor of Figure P18.18 by using the rules for resistors in series and parallel. (b) Write three independent equations for the three currents using Kirchhoffs laws: one with the node rule; a second using the loop rule through the battery, the 6.0- resistor, and the 24.0- resistor; and the third using the loop rule through the 12.0- and 24.0- resistors. Solve to check the answers found in part (a). Figure Pl8.18
(a) Find the current in each resistor of Figure P18.18 by using the rules for resistors in series and parallel. (b) Write three independent equations for the three currents using Kirchhoffs laws: one with the node rule; a second using the loop rule through the battery, the 6.0- resistor, and the 24.0- resistor; and the third using the loop rule through the 12.0- and 24.0- resistors. Solve to check the answers found in part (a). Figure Pl8.18
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
Check Your Understanding When using Kirchhoff’s laws, you need to decide which loops to use and the direction of current flow through each loop. In analyzing the circuit in Example 10.7, the direction of current flow was chosen to be clockwise, from point a to point b. How would the results change if the direction of the current was chosen to be counterclockwise, from point b to point a?
Check Your Understanding If you place a wire directly across the two terminal of a battery, effectively shorting out the terminals, the battery will begin to get hot. Wiry do you suppose this happens?
Check Your Understanding In considering the following schematic and the power supplied and consumed by a circuit, will a voltage source always provide power to the circuit, or can a voltage source consume power?
A 0.50-W, 220- resistor carries the maximumcurrent possible without damaging the resistor. If the current were reduced to half the value, what would be the power consumed?
Residential building codes typically require the use of 12-gauge copper wire (diameter 0.205 cm) for wiring receptacles. Such circuits carry currents as large as 20.0 A. If a wire of smaller diameter (with a higher gauge number) carried that much current, the wire could rise to a high temperature and cause a fire. (a) Calculate the rate at which internal energy is produced in 1.00 m of 12-gauge copper wire carrying 20.0 A. (b) Repeat the calculation for a 12-gauge aluminum wire. (c) Explain whether a 12-gauge aluminum wire would be as safe as a copper wire.
If you wish to take a picture of a bullet traveling at 500 m/s, then a very brief flash of light produced by an EC discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one EC constant is acceptable, and given that the flash is driven by a 600F capacitor, what is the resistance in the flash tube?