4) A stepped steel shaft consists of hollow shaft 2 m long, with an outside diameter of 100 mm and inside diameter of 70 mm, rigidly attached to a solid shaft 1.5 m long, and 70 mm in diameter. Determine the maximum torque which can be applied without exceeding a shearing stress of 70 MPa or a twist of 2.5° in the 3.5 m length. Use G = 83 GPa. 2.00m 1.50m .... .. ... 100mm_ 70mm

4) A stepped steel shaft consists of hollow shaft 2 m long, with an outside diameter of 100 mm and inside diameter of 70 mm, rigidly attached to a solid shaft 1.5 m long, and 70 mm in diameter. Determine the maximum torque which can be applied without exceeding a shearing stress of 70 MPa or a twist of 2.5° in the 3.5 m length. Use G = 83 GPa. 2.00m 1.50m .... .. ... 100mm_ 70mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid stainless steel [G = 12,500 ksi] shaft that is 30 in. long will be subjected to a pure torque of T = 265 lb-in. Determine the minimum diameter D required if the shear stress must not exceed 8,000 psi and the angle of twist must not exceed 0.050 rad. O 0.709 in. 0.373 in. 0.600 in. O 0.429 in. O0.542 in.
Question 5 of 10 -/10 View Policies Current Attempt in Progress A solid 1.500-in.-diameter steel [G = 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and Tp= 80 lb-ft, acting in the directions shown. Assume a = 42 in., b = 78 in., and c= 30 in. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque Tc that can be applied to the shaft. y TB Te Tp (1) (2) (3) B D b. Answer: Tc- i andrew aytona iadd sa fb Ib-ft eTextbook and Media Attempts: 0 of 3 used Submit Answer Save for Later Using multiple attempts will impact your score. 5% score reduction after attempt 1
A torque of Tp = 1320 N-m is applied to gear D of the gear train shown. The bearings shown allow the shafts to rotate freely. Assume shafts (1) and (2) are solid 35-mm-diameter steel shafts. Determine the magnitude of the maximum shear stress acting in shaft (2). 230-mm dia. Tp D (1) 150-mm dia. О 171.6 МРa O 96.0 MPa O 156.8 MPa O 184.8 MPa O 111.2 MPa
(+) The hollow shaft used in the system has the following conditions: В E Outer Ø: 110 mm Ø Allowable Shearing Stress: 85 MPa 18 KN•M Determine the thickness (mm) of the shaft. Round to the F 35 kN-m nearest whole number for the thickness and use 2 decimal places for other solved values. Provide 88 kN m a torque diagram, strictly follow instructed sign convention, and start from left to right. 35 kN-m
A solid 1.250-in-diameter steel shaft is subjected to torques Tg- 190 Ib-ft and Tp- 115 Ib-ft, acting in the directions shown. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque Tethat can be applied to the shaft. Te Tp Ib-ft Answer: Te= i
A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a pure torque of T = 2920 lb-ft. Determine the maximum inside diameter d that can be used if the shear stress must not exceed 8,000 psi and the angle of twist must not exceed 3° in an 8-ft length of shaft. O 2.91 in. 1.85 in. 3.74 in. O2.43 in. O 2.71 in.
Save Answer The 101-mm-diameter steel shaft is subjected to the torques shown. T1 = 10 kN-m, T2 = 4 kN-m, T3 3 kN-m. Determine the angle of twist (in degrees) of the end B. Use L1 = 0.73 m., L2 D 0.52 m., L3 = 0.70 m. Shear modulus = 72 GPa. Round off to two decimal places. Input the numerical value only. A D T3 L3 L2 T2 L1 T1
An shaft consist of a hollow shaft 3m long, with an outside diameter of 200mm and an inside diameter of 150mm, rigidly attached to a solid shaft 2m long with a diameter of 150mm. Determine the maximum torque which can be applied without exceeding a shearing stress of 70 MPA or a twist of 4.3° in the 5m length. Use G=83 GPA.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (see figure). 1.50 in. 0.75 in. B A To - 6.0 in. 15.0 in. (a) If the allowable shear stress in the shaft is 2,760 psi, what is the maximum torque (T)max that may be applied at section C? (Enter the magnitude in Ib-in.) Ib-in. (b) Find (T)may if the maximum angle of twist is limited to 0.226°. Let G = 10,600 ksi. (Enter the magnitude in Ib-in.) Ib-in.
Determine the maximum torque of the tube shown if the allowable shearing stress is 58 Mpa. Given: t = 2.79 mm and a = 43 mm. Answer must be in kN-m. a 32°C Lig P3 43. KA EDCA ESC F7 FB E RU H. M.
Question 1 of 10 View Policies Current Attempt in Progress X- K Answer: P A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 1.9 in. The shaft is subjected to a tensile axial load of P = 9 kips and torques TA = 8 kip-in. and Tg = 33 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. > (1) H N B TB (2) - / 10 K E
An steel shaft consists of a hollow shaft 3m long, with an outside diameter of 200mm and an inside diameter of 150mm, rigidly attached to a solid shaft 2m long with a diameter of 150mm. Determine the maximum torque which can be applied without exceeding a shearing stress of 70MPa or a twist of 4.3° in the 5m length. Use G = 83GPa. 200mm 150mm 6 6 3m 2m