4-9 A mass of 5 kg of saturated water vapor at 150 kPa is heated at constant pressure until the temperature reaches 200°C. Calculate the work done by the steam during this pro- cess. Answer: 214 kJ

Q: stem: *

A: In this question it is required to select the correct answer from give option

Q: What is the full form of: (1) CAD (2) CAE (3) CAM

A: CAD - Computer Aided Design

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: Write the advantages of CAD/CAM and limitations of CAD/CAM.

A: CAD (Computer-Aided Design) and CAM (Computer-Aided Manufacturing) are two closely related…

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: What are some ways to make sure the proper codes are being posted when using CAM software?

A: Given CAM software To find Verify the actual codes with generated codes

Q: Explain briefly the sorts of interruptions and why they are crucial to the machine.

A:

Q: am Delik

A: The core is designed as shown below.

Q: Which organization sets the standards for dimensioning and tolerancing practices?

A: Given Data⇒ standards for dimensioning and tolerancing practices Problem statement⇒ Problem says…

Q: What G-code designates IPM feed rate mode? IPR feed rate mode?

A: CNC machine feed rates are often specified in either inches per minute (IPM) or inches per…

Q: Identify the parts of the square nose end mill

A: 1. Ans: Option C John reports it to Rachel. Rachel wears a gas mask and then places loose spill…

Q: List any two criteria that compares a Numerical Control (NC) and Computer Numerical Control (CNC)…

A: Numerical Control (NC): It is type of machine which is controlled by a set of data (program). In the…

Q: Demonstrate reed type comparator with the help of examples and figure.

A: Reed type comparator,

Q: This a sketch of what process. V, F Punch Flash Die Cutting edges Select one: a. Cutting O b.…

A: The given sketch represents Trimming process. Trimming process: The shearing of the excess material…

Q: What is flexibility? Why there is a need of flexiblity in manufacturing system? Sketch elements of…

A: Solution:

Q: How long will it take the vibration table to do a sine sweep from 2 to 256 Hz at a rate of 2…

A: To calculate the time taken first the number of octaves have been calculated for given frequency…

Q: how to position this locator on a plate base for a part to ensure conformance with the Production…

A:

Q: Briefly explain the methodsto check the phase sequence of the machines?

A: This question is based on the concept of phase sequence testing

Q: Select appropriate sensors for a specified wire cutting system

A: To select appropriate sensors for a wire cutting system, it would be helpful to have more specific…

Q: Make Cartesian graphics for CNC milling and draw Cartesian graphics on the machine spindle (show X,…

A: Given Milling CNC To find CNC milling Cartesian format Machine spindle movement in the Cartesian…

Q: How do you know whether the toolpath is correct before you write the code for it in a CAM system

A: The employment of software and computer-controlled gear to automate a manufacturing process is…

Q: Which method of tolerancing does not exist? Limit tolerance Unilateril tolerance O Triolateral…

A: Tolerance is allowable variation of a given dimension from some reference.  unilateral tolerance…

Q: ake a comparative study of 4-stroke SI and CI

A: given: Make a comparative study of 4-stroke SI and CI egines

Q: Disposal of universal lathe machine Below is the example format what i needed.

A: Safety precautions/disposal of universal lathe machine while operating for operations: Use proper…

Q: Which one of the part definitions is right? O A part is an unit which is involved in the final…

A: Solution:

Q: In CNC machines for every work the punched tapes are cycled through the tape reader Select one: True…

A: In CNC machines for every work the punched tapes are cycled through the tape reader Select one:…

Q: Creo Software to perform the assembly operation for a shaft and hole system. Hint: you can choose…

A: we have to demonstrate the assembly feature in creo parametric

Q: Question 1: (answer must be handwritten) What is special about timing belts compared to classic flat…

A:

Q: contrast different input devices in cad/cam sections

A: CAD(Computer aided drawing) consist of input devices, output devices, processors.

Q: In GD&T   When tolerancing elongated holes, no ____________________ precedes the tolerance in the…

A: When tolerancing elongated holes, no diameter symbol precedes the tolerance in the feature control…

Q: Estimate the heat transfer rate (kW) at which an automotive radiator would operate if an engine…

A: For the cooling process in the engine:- 1. 44% of the heat generated is exhaust gas emission 2. 8%…

Q: A inch quadruple 16 the screw is rotating at

A:

Q: Draw feature control frame (FCF) of the following characteristics: Profile of line tolerance zone…

A: Profile of line tolerance zone .500 at LMC to datum A.Angularity with tolerance zone 0.10 at MMC to…

Q: 1. All orientation controls must have maximum material condition a large tolerance zone O red text…

A: Orientation control is a geometric tolerance that defines the orientation of the part with respect…