4-31. The concrete column is reinforced using four steel reinforcing rods, each having a diameter of 18 mm. Determine the stress in the concrete and the steel if the column is subjected to an axial load of 800 kN. Es =200 GPa, E =25 GPa. %3D $4-32. The column is constructed from high-strength concrete and four A-36 steel reinforcing rods. If it is subjected to an axial force of 800 kN, determine the required diameter of each rod só that one-fourth of the load is carried by the steel and three-fourths by the concrete. E=200 GPa, E.=25 GPa. 800 kN 300 mm 300 mm Probs. 4-31/32 auhiected

4-31. The concrete column is reinforced using four steel reinforcing rods, each having a diameter of 18 mm. Determine the stress in the concrete and the steel if the column is subjected to an axial load of 800 kN. Es =200 GPa, E =25 GPa. %3D $4-32. The column is constructed from high-strength concrete and four A-36 steel reinforcing rods. If it is subjected to an axial force of 800 kN, determine the required diameter of each rod só that one-fourth of the load is carried by the steel and three-fourths by the concrete. E=200 GPa, E.=25 GPa. 800 kN 300 mm 300 mm Probs. 4-31/32 auhiected

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve stresses in members BD, BE and CE. (answers should be in psi) You can use any method. Kindly show complete and handwritten solution if possible.
The hollow core panel is made from plain stone concrete. Determine the dead weight of the panel in kips. The holes each have a diameter of 5 inches. The unit weight of concrete is 144 lb/ft³. 10 in. | -12 in 12 in 12 in 12 in 12 in 12 in. 12 ft
A rectangular concrete beam has a width of 300mm and an effective depth of 550mm. The cantilever beam is loaded as shown. Assume f = 21 MPa and fy = 312 MPa. Compression reinforcement if necessary shall be placed at a depth 80mm from the outermost compression concrete. Determine the required number of 25mm tension bars. Draw the details of the rectangular beam. 20 kN/m 3 m 2 m 2 m 40 kN
Find the safest value of load "P" for the beam loaded shown. fc'=35MPA, Use GRADE 420 steel bar and n=10 The answer is kN. Assume unit weight of concrete = 24kn/cu.m. 200 3 m 1 m toort twit 3P 70 200 2-20 mm O 330 3. BEAM 4-32 mm Ø 300 100 DIMENSIONS ARE IN "mm"
The plan of a reinforced concrete column section, and the distribution of strains at the ultimate limit stage are shown below. The concrete is M20 grade and the steel of Fe 250 grade. Also sketched below, for convenience, are the concrete compression stress block and the design stress-
Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with the ties between vertical braces spaced every 2 ft, what force is exerted on the bottom tie? Brace Form 9 ft Concrete Bottom tie
Principle of Reinforced Concrete Design
ll中国移动 4G PN © 11:50 PM 75% 4 A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. - 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength ofS, - 360 N/mm. The spirals are 10@50 with the yield strength of f,- 270 N/ mm². If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
1/ Calculate maximum deflection of the beams (This was solve it) 2/ Check the suitability of the section assuming the code limitation of L/240. 3/ If maximum deflection doesn’t meet the code requirement, propose your solution
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
Plz
A circular Column has dia of D 30 in. Concrete Compressive strength at 28 days is of steel is (60 + 60) ksi. Determine the design capacity of circular column and 8 # 11 bars is used. (4 + 60) ksi and yielding strength