4-1) Distortionless transmission A bandpass signal g(t) of bandwidth B = 1200 Hz centered at f= 10 Hz is passed through the RC filter below with RC = 105. If over the passband, a variation of less than 4% in amplitude response and less than 8% in time delay is considered to be distortionless transmission, would g(t) be transmitted without distortion? Find the approximate magnitude response and the approximate time delay for the signal.

4-1) Distortionless transmission A bandpass signal g(t) of bandwidth B = 1200 Hz centered at f= 10 Hz is passed through the RC filter below with RC = 105. If over the passband, a variation of less than 4% in amplitude response and less than 8% in time delay is considered to be distortionless transmission, would g(t) be transmitted without distortion? Find the approximate magnitude response and the approximate time delay for the signal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that lets the spectral components pass between the fa=12kHz and fb=16kHz sequences. If you are using a 32-tap FIR filter. What is the value of the central frequency, f0, in Hz of the band that passes the filter? And what is the outline of the frequency response for the filter passes bands?
The frequency multiplier is a non linear device followed by a bandpass filter, as in fiğure- Suppose that the ideal square - law device with: Shown non linear device is an imput - output charaderistics : e,(+) = ae?c+) YCt) I egc+) Non linear device eac+) BPF Determine the output yct) if the input is an FM signal given by e;l+) = A cos (Wet+ B sinwmt)
Question 7: The signal x(t) = =2 cos(60nt) +3 cos(100nt) is sampled at S = 120 Hz. a. Find the minimum number N of samples necessary to prevent leakage. b. Find the frequency spacing (resolution). C. Determine the amplitude values of the DFT.
A sinusoidal haseband signal with a frequency of 5kHz is transmitted using DSB-LC. The received signal is R = 10[1 +0.2 cos(2m5000r)] cos(2r10°r) Volts. The shown system is used as a receiver. The BPF is ideal and its center frequency is 1.002MHz and bandwidth 7kHz. The demodulator has input-output characteristics (V, = 4V/). The LPF is ideal with an adjustable cutoff frequency. Determine the output signal waveform of this system. You need to specify the cutoff frequency of the LPF to obtain the original message back at Y. R BPF Demodulator B (B-4A) LPF DC removal
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (lo in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1, and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. The quality factor (Q1) for curve 1 is about: 7.5 5- 2.5 1-10 1-10 1-10 1-10 Frequency (f), Hz O a. 20000 Hz O b. 0.5 O c. 0.23 O d. 2 O e. 1.5
i need the answer quickly
This figure illustrates the magnitude spectrum X(w) for bandpass signal x(t). Highest frequency is 30Hz -30 20 it X(w) 0 J (Hz) 20 Sketch the magnitude spectrum of the signal sampled at 60Hz 30 Can x(t) be reconstructed from the resultant spectrum using a band[ass filter? Sketch the magnitude spectrum of the filter design if it can, given the resultant spectrum
An inductive proximity sensor is used to detect the presence of car in traffic lights. The output circuit of the sensor produces a sinusoidal signal at 20 KHz. This signal is usually mixed with a random high and low frequency noise around the signal. Design a suitable cascaded bandpass filter to remove the unwanted signals given that the passband region is not more than 4 KHz. Also, sketch the magnitude and phase responses of the filter.
Circle final answer & Answer it in rad/s. Keep three significant figures.
a ) Using 0.1 pF capacitors , design an active broadband first - order bandpass filter that has a lower cutoff frequency of 200 Hz , an upper cutoff frequency of 2000 Hz , and a passband gain of 0 dB . b ) Write the transfer function for the scaled filter . c ) Use the transfer function derived in part ( b ) to find H ( wo ) where wo is the center frequency of the filter . d ) What is the passband gain ( in decibels ) of the filter at wo ?