-30 in. RA 800 lb -60 in. - 1600 lb D 30 in.→ B RB

Q: FIGURE 1. 40 kN 40 kN/m A B 20 kN/m E ए 2 m 1m 4 m 2 m R, R2 What is the maximum intensity of moment…

A: Draw SFD and BMD and answer the questions

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: 不 k H, k2 H3 k3 NOTE: ト -ごー*

A:

Q: E A F D 3 in. in. G -2 in. 1.5 in B

A:

Q: Determine the coordinates of the centroid for the shaded area

A:

Q: Q5-) Explain the standard consistency Procedure? according to the guide manual No. 1042@2011.

A: The standard consistency of a cement paste is outlined as that consistency which is able to allow…

Q: & Find the set of solutions xy dx + (y-3x²) dy = 0. %3D

A:

Q: For the section shown below verify the following equations (7) Z section th'b' (b+h 12 (26+h B D C

A: Consider the given figure So here we have to verify J=t332b+hI12=th2b312b+h2b+h

Q: determine the centroidal axis xx of the section shown in the figure

A: The given section can be break into two rectangles, Let the unit of all dimensions are in mm,

Q: Draw the F.B.D and kindly find the solution for this. May I request to please make the solution…

A: This is Strength of material problem . In this problem ,Given Angle of Cable and Ask about Tenion in…

Q: p² – 3r + 2 lim r-1 r - 1

A:

Q: DRAW THE SECTION INDICATED BY THE CUTTIN

A: Any view obtained by a projection on a plane other than the horizontal, frontal, and profile…

Q: Determine maxium principal plane

A: We have to determine the maximum principal plane.

Q: Compute the sinA =0.4785 cosB= -0,52d -0.52d %3D tanc= 0 987

A: Converting the given values into the degree is a very simple and easy way. We can convert the given…

Q: at state of given (All in The Stres point is MPa) 80 100 100 i) And Principal Stren & Principal…

A:

Q: Problem No. 8 For the arch shown in Figure 8 determine the Reaction Support Reaction Components at…

A:

Q: Define deflection angles.

A: A deflection angle is an angle between the onward extension of the previous leg and the line ahead.…

Q: Use the unit load method to calculate the vertical displacements at the quarter and mid-span points…

A: The given figure is shown below:

Q: Shape PNA L5x3x1 -X x²/16 x x5/16 x¼ PNA k Wt. Table 1-7 (continued) Angles Properties Area, A Axis…

A: As multiple questions are asked and as per the guidelines only very first question will be answered.…

Q: - What is the meaning of Cant in Turkish? A) aliyman B) clearance C) dever D) slope E)…

A: Meaning of Cant

Q: Discuss Designing for Shear

A: Introduction : Shear stresses in design normally operate in planes perpendicular to a member's…

Q: 4 in 2 in 4 in 8 in -12 in- -16 in-

A:

Q: 350 mm 45 KN B 500 mm 9 kN C 9kN FD KN 400 mm D Wall

A:

Q: (0 KN 15KN DU む oam 0.am J 1.2met>2mt l.zmel

A:

Q: Make whatever changes or addition are necessary in each case to form a correct and complete FB.D.

A: 1) Incorrect, weight mg will act downwards 2) Incorrect, there will be frictional force acting at…

Q: prove tañcy) dy

A: Proof of integration ###

Q: :Draw I.L for members a, b, c & d. F G b H 4m 1 3m 3m 4m 3m

A:

Q: The moment diagram by parts are base on the moment diagram of O Fully restrained beam O Cantilever…

A: Moment diagrams by parts is a method to solve the determinate beam and find reactions in beam.

Q: A CPLD is based on

A: A CPLD- Complex Programmable logic device It is a programmable device based on complexity PALs and…

Q: GO KN 30 KN R. R2

A: - To find : Support reactions R1 and R2

Q: Which shortcut key lets you rotate the drawing area? RO О тв O z O L

A:

Q: Additional Problem: The wall crane supports a load of 7 kN. Determine the horizontal and vertical…

A:

Q: The square slab of Fig. P15.1 is simply supported by masonry walls along all four sides. It is to…

A: A Slab is a structure that is highly resistant to loads that are later used on a stake axis. A…

Q: D O00 15KN 15KN B.

A: Given data : Number of member (m)=13Number of external support reaction (R)=2+1=3Number of joint…

Q: draw One-way slab- 12 mm diam. main bars spaced @        300 mm o.c. b/w with 10 mm diam. extra top…

A: Solution: Given: One-way slab: Main bars = 12 mm diameter Temperature bars = 10 mm diameter

Q: Draw a neat and clean diagram of the final configuration of how the bars are placed.

A: To draw the bar configuration of the given beam

Q: 16-11.828⁰ 9-2 9-5.828¹ 10.342 8x8 POST PIO 12-11.342* 6-5.143* TT 8x12 RAFTER P109 8x8 POST P102…

A: free body diagram of the bottom chord

Q: (2 2' 3 4 8570 PROBLEM 1 2720 3580 1500 (A 202 1 2 The Figure on the right is a 2nd Floor Structural…

A: To find one way or two way slab

Q: d²y ¸ dy + 7. - бу 3D 36х dx² dx

A:

Drainage of Pavements

Pavement Drainage holds ample significance, as it prevents the accumulation of water or any liquid on the surface of pavements and ensures proper drainage system. With proper design and gradual slopes provided, the water gets easily removed from the surface into the drains, which are essential during heavy rains and unusual weather conditions keeping it less prone to accidents and increasing the durability of the pavement structure.