answer quickly The water is siphoned out of the tank shown in Figure Q4 (b). Determine the flowrate from the tank and the pressures at points (1) and (2).(b)30 cm|(2) ▼(3)45 cm50 cm1 cm(1)Figure Q4 (b)|

Answered: 30 cm |(2) (3) 45 cm 50 cm 1 cm (1)

Engineering

Mechanical Engineering

30 cm |(2) (3) 45 cm 50 cm 1 cm (1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the tank system shown, there is a constant flow (1) (2) rate of Q into tank 1. Initially tank 1 is at the height of h0 while all other tanks are completely empty. (a) Draw a block diagram representation of the following system. (3) of
Q3: A cylindrical tank of radius R=1.5 m and height H = 3 m initially filled with water. At the bottom of the tank there is a hole of radiusr = 20 cm, through which water drains under the influence of gravity. Find the depth of water at tim e 30 second, and determine how long it takes the tank to drain completely?
A turbine (see the figure of Example IIIa.3.21) is located at an elevation H1 from the surface of a lake with the discharge pipe located at an elevation H2 from the turbine centerline. Find flow velocity, V4 in terms of H1, H2, P1, P4, h,, and p where subscript 4 refers to the discharge piping. [Ans.: V, = (2/p)[(R – P.) + pg (Z, – Z, –h,)]. Lake H, h. D2 4 D4 H4 Turbine
Water flows from a large tank through a large pipe that splits into two smaller pipes, as shown in the figure below. The flow can be considered inviscid and steady state. Assume d1 = 1.5 cm, d2 = 2 cm, z = 8.5 m, and h = 3.5 m. Determine the level of the tip of the inclined pipe such that the flowrates exiting both small pipes are equal. Z diameter d diameter d
b) What is the volume flow rate through the pipe, in m³/s? Yanıtınız
3. A circular cylinder of radius a is fitted with two pressure sensors to measure pressure at 0 = 180° and at 150°. The intent is to use this cylinder as a stream velocimeter, i.e. a device to determine the velocity of a stream by measuring the pressures at the two taps. The fluid is incompressible with a density of p. Figure for Part (a) U Figure for Part (b) 30 a) Using potential flow approximation, derive a formula for calculating U from the measured pressure difference at the two pressure taps. Note that for accurate measurement, the velocimeter must be aligned to have one of the taps exactly facing the stream as shown in the figure. (Ans: 2|Aptaps|/p ) b) Suppose the velocimeter has been misaligned by ổ degrees so that the two pressure taps are now at 180° + 8 and 150° + 8. Derive an expression for the percent error in stream velocity measurement. Then, calculate the error for 8 = 5°,10° and –10°. (Ans: [2/(sin2(150 + 8) – sin²(180 + 8) )– 1] × 100 )
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibr/in.? g = 32.0 ft/s² Water v = 0.01604 ft/lb Determine the difference in pressure between points a and b, in Ibf/in2?. Does the pressure increase or decrease from point a to point b? Sten 1
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft3/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibf/in.? g = 32.0 ft/s² Water v = 0.01604 ft³/lb Determine the difference in pressure between points a and b, in Ibf/in?. Does the pressure increase or decrease from point a to point b?
The open tank in the figure contains water and is being filled through section 1. Assume incompressible flow. If the water level h is constant, determine the exit velocity V, for the given data V, = 3 m/s and Q3 = 0.01 m/s. Q -0.01 ms D, =5 cm D3 =7 cm Water
Water enters a fountain through a pipe with a cross-sectional area A₁ at a flowrate Q. The pressure in the inlet pipe is p₁. The water then leaves through a nozzle with a cross- sectional area A2 and at an angle 0, as shown in Figure Q5. Both the inlet and the nozzle are at a height h2, and the jet reaches a maximum height h3. X You may assume that viscosity is negligible. a) Find the horizontal force on the block b) What is the horizontal-component (u₂), vertical component (v₂) and magnitude (V₂) of the velocity of the jet as it leaves the nozzle? = c) What is the maximum height of the jet? You may assume that the horiztonal component of velocity is the same at every point in the jet.
In the figure shown below the water comes out of a tank and runs through pipe 1 (D1=10cm) that splits into two smaller pipes open to atmosphere (D2=3cm D3=6.5cm). The pressure shown in the tank manometer is 10kPa. Deermine the flow velocity in pipe 1 considering a perfect fluid.
Find the horizontal and vertical forces to hold stationary the nozzle shown in the figure below. The fluid flowing through it is 10 °C liquid water; A₁ = 1.2 m², A₂ = 0.300 m², V₁ = 15 m/s, p2 = Patm and p₁ = Patm + 75 kPa. Neglect effects of gravity. Fx= i Fy= i A1 P1 KN kN Fy ZA A2, P2 = Patm Fx 45° Patm