3.66 A long water trough of triangular cross section is formed from two planks as is shown in Fig. P3.66. A gap of 0.25 cm. re- mains at the junction of the two planks. If the water depth ini- tially was 0.6 m, how long a time does it take for the water depth to reduce to 0.3 m? 0.6 m boonly 0.25 cm V 90°-

3.66 A long water trough of triangular cross section is formed from two planks as is shown in Fig. P3.66. A gap of 0.25 cm. re- mains at the junction of the two planks. If the water depth ini- tially was 0.6 m, how long a time does it take for the water depth to reduce to 0.3 m? 0.6 m boonly 0.25 cm V 90°-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.66 A long water trough of triangular cross section is formed from two planks as is shown in Fig. P3.66. A gap of 0.25 cm. re- mains at the junction of the two planks. If the water depth ini- tially was 0.6 m, how long a time does it take for the water depth to reduce to 0.3 m? 0.6 m V 90°- 0.25 cm 11 15190 FO
27 KN A 2m B 30⁰ 22 kN 3m 6. In Figure 2, Which of the following gives the distance of the resultant from point A? a. 0.38m b. 0.56m c. 1.42m d. 1.85m e. 2.56m f. NOTC C 7 kN 60⁰ FIG. 2
A built-up section consists of two miscellaneous channels MC 18 × 42.7 and one cover plate 12 mm x 500 mm. The channels are placed at 300 mm back to back with the flanges outstanding. a) Determine the Ina(x)- b) Determine the Inav)- Properties of MC 18 × 42.7: A = 8129.02 mm² tw = 11.43 mm d = 450 mm Ix = 230.59 x 106 mm* br = 100.33 mm ly = 5.99 x 10° mm* %3D tf = 15.88 mm x = 22.28 mm MC 18 × 42.7
F2-10. Determine the magnitude of the resultant force of the water acting on the triangular end plate A of the trough. Neglect the width of the opening at the top. How far does this force act from the surface of the water? 1.2 m 0.3 m 0.3 m
7. The mass less, 1.2 m wide gate shown in fig. (2.7) pivots about the frictionless hinge (O). It is held in place by the 8.9*10' N counterweight, (). Determine the water depth,(h). 3 Scanned with CamScanner Water Gate Pivct 0 Width - 1.2 m 0.6 in 0.9 m Figure (2.7)
Q/Complete the dam section dimensions and then find the moment of all considered forces about the toe? Take C=0.6, 3 25 KN/m, S̟ = 2.4, H = 9 m. H-78 KN Y. = 10-, Y, = %3D %3D %3D H, = 2a/5, – C F.b Hi Ww1 Fsh2 Fsys PE Ww3 Fsv W2 Fsh Wwa/ Fsh Wi b=9 m C. Yw.H' C. Yw.H Tus CY,H' + (C. Yw. H – C. Yw. H')
For questions 3A and 3B, refer to the shear and moments diagrams shown. 3A. What is the slope of the tangent line [indicated by black bold line] as shown in the moment diagram? * 10.21 8.03 Area 2.21 Shear Diagram -5.79 -6.32 -9.97 -13.79 Tangent Line 9.28 7.42 Moment Diagram -5.00 -12.16 Figure for Questions 3A and 3B -9KN -10KN -11 KN
Find the net hydrostatic force per unit width on the rectangular panel AB in figure 3-21 2m 1m Water 2m Glycerin y-1236 KN/m3 1m Fig. 3-21(a) O a. 29.04 o b. 78.48 c. 12.36 d. 49.44
Tank filles with water as shown in fig. fing the hevi Zental and vertical hydrostatic Force on the Part CD, BC . AB. use The informution :- Cylinder radiug R= 0,5m %3D Reading of 5=1S KPa The hidh CH) = 3.5 m %3D The width of the ey linder = ym G Tank Full of Water Width = b H R
Solve the value of Ely 1m from the free end. 6 kN 2 kN/m 4 kN A -1.5 m-1.5 m- m 3 m -28.92kNm^3 O-1070kNm^3 -34.25kNm^3 O-505kNm^3 B
2. Draw the FBD of the entire structure C 18 kN 2 m В 2 m 2 m -3.6 m-
1.A) Draw the free body diagram for the right-hand side part. 1.B) H B 4 m+ 80 kN.m 4 m 5 m G 5 kN 15 kN An imaginary cut a-a B a a 4 m F 3 kN Draw the free body diagram for the right-hand side part. a 4m An imaginary cut a-a a -5 m 2 m 4 m E 5 kN/m