3.6/ A landing gear system has repetitive stresses placed on it twice a day as a result of landings. The probability of a failure during landing is 0.0028. Determine the reli- ability of the landing gear system over a 30-day contingency operation. What is the probability of a failure occurring between days 10 and 20 of the operation?

3.6/ A landing gear system has repetitive stresses placed on it twice a day as a result of landings. The probability of a failure during landing is 0.0028. Determine the reli- ability of the landing gear system over a 30-day contingency operation. What is the probability of a failure occurring between days 10 and 20 of the operation?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.1. Journal bearings are one of the most common types of hydrodynamic bearings. Their primary purpose is to support a rotating shaft. The bearing has a shaft diameter of 93.00 mm with a unilateral tolerance of -0.02 mm. The bushing bore has a diameter of 93.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2300 N. The journal speed is 820 rev/min. For the minimum clearance assembly, determine: a) Sommerfeld number, minimum film thickness and heat loss rate for SAE 10 at 52.5°C film temperature. b) Sommerfeld number, minimum film thickness and heat loss rate for SAE 60 at 70°C temperature.
Evaluate and identify nearest value of the load that can be lifted to a height of 1000 cm in 0.50 minutes by a machine which has an input power of 0.65kW. a. Approximately 0.3 ton. b. Approximately 0.6 ton. c. Approximately 0.2 ton. d. Approximately 0.4 ton.
When design for a cyclic load, if in one case, the designed reliability is 0.99, what is the approximate reliability factor which should be used according to the textbook? 1.0 0.9 0.81 0.75
The worker in the loading zone has been complaining about fatigue and the lack of rest. You measure his heart rate and find it to be 125 beats/min and slowly increasing during work. When he sits down, the heart rates dropped to 120 beats/min by the end of the first minute of rest and 100 beats/min by the end of the third minute. Based on heart rate guidelines, does the worker work with a good working condition and have sufficient rest? Yes No ◆
rev/min Q2: a/ an engine producing 12 kW power at 3000 rev/min is fitted to a vehicle with a mass of 700 kg. if the rolling resistance is 130 N determine the maximum gradient this vehicle could climb in top gear with a 4.5:1 final drive ratio, a transmission efficiency of 70%, and a wheel radius of 0.28 m. أدخل نص
A) If we consider a transmission ratio 1 to 5, in the arrangement of pulleys shown. and the tangential speed in the shaft (diameter of 30mm) where the driving pulley is coupled is 1.5 m/s. What is the rotational speed of the driven pulley (in rpm)? B) From the previous exercise. What is the length of the transmission band (belt) calculated in the previous exercise? Motriz 0.30 m 1.5 m uc=0.35 -0.30 m- 0.40 m Movida -0.30 m 0.30 m d=0.10 m e-0.05 m
QUESTION 1 A suitable factor of safety to apply when selecting the cable for a factory hoist is: 05 O1.2 0.2 O 25 QUESTION 2 A winch drum of diameter 199mm turning at 14rpm lifts a load of 5.5kN. What is the winch output power? Give your answer in W to 1 decimal place without units eg 102.3 NOT 102345239 W QUESTION 3 The figure below shows two proposed designs of drums to solve the same load and line speed lifting arrangement. What is the biggest advantage with design A: A The torque on the drum shaft will be lower O The rope speed will be lower The bending moment in the drum shaft will be lower O The weight of the drum material will be less 刚 B
Calculation of Limits using ANSI B4.1 Standard Tables, when one of the design Features Exists. When calculating the limit tolerances for features that mate with purchased parts, the purchased part size must be known. This may be obtained be requesting a drawing from a vendor or, a caliper or micrometer can be used to obtain an accurate size. A shaft diameter of 1.2500" is to be pressed into a part using a FN3 interference (force) fit. Limits of size for the shaft diameter are 1.2500" and 1.2495". Determine the Limits of the hole diameter. Show all work.
5) Which statement is true about the friction factor in the Moody diagram (shown below). Moody Diagram 0.1 0.09 Transition Region 0.08 0.07 0.05 0.04 0,06 0.03 0.05 0.02 0.04 0.015 0.01 0.03 0.005 0.002 0.001 5x10-4 2x10-49 10-4 5x10-5 10-5 5x10-6 10-6 Friction Factor 12---- Laminar Flow 64 Material Concrete, coarse 0.25 0.025 Concrete, new smooth Drawn tubing 0.0025 Glass, Plastic Perspex 0.0025 Iron, cast 0.15 Sevens, old 3.0 0.1 Steel, mortar lined Steel, rusted 0.5 Stoel, structural or forgod 0.025 Water mains, old Friction Factor=AP. 1.0 Smooth Pipe 3000 10³ 10¹ 105 106 107 108 Reynolds Number, Re - Vd P a) The lines for different relative roughness in the turbulent regime correspond to Darcy-Weisbach model b) The lines for different relative roughness in the turbulent regime correspond to Nikuradse model c) The lines for different relative roughness in the turbulent regime correspond to Hazen-Williams model d) The lines for different relative roughness in the turbulent regime…
A ball bearing, rotating at 1200 revolutions per minute, operates at a radial equivalent load of 29% of its dynamic load rating. What is the expected lifetime in hours at a reliability level of 90%? Please round your answer to the nearest hour. Type your answer...
Q12. (а) Differentiate between the "soft constraints" and “hard constraints".
In mechanic resistance