3. With two devices X and Y and the simplex mode of serial data transmission between the two, data can be: A Simultaneously transmitted from X to Y and Y to X. B Only transmitted in one direction, X to Y or Y to X, at once. C Sequentially transmitted, for example, from X to Y followed by Y to X. D Only ever transmitted in one direction, for example, X to Y but not Y to X.

3. With two devices X and Y and the simplex mode of serial data transmission between the two, data can be: A Simultaneously transmitted from X to Y and Y to X. B Only transmitted in one direction, X to Y or Y to X, at once. C Sequentially transmitted, for example, from X to Y followed by Y to X. D Only ever transmitted in one direction, for example, X to Y but not Y to X.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are the applications of vibration motor and Vacuum Pump in Mechatronics systems?
A 200V, 875rpm, 160 A separately excited dc motor has an armature resistance of 0.07Ω. It is fed from a single phase fully controlled rectifier with an ac source voltage of 230V, 60Hz. Assuming continuous conduction. Determine i) Back emf ii) Firing angle for rated motor torque and -500rpm iii) Motor speed for α = 160° and rated torque. iv) Firing angle for rated motor torque and 700rpm.
A dc motor 120 volts has 100 ampere rated current. The allowable voltage drop of 3% of input voltage. Find the maximum distance from the supply if the wire has a diameter of 316 mils and the resistivity of wire is 10.4 ohm-cmf.
The armature circuit of a free excited direct current motor with a nominal voltage of 600 V is fed from an adjusted direct voltage source. The excitation circuit is also powered from a regulated voltage source. It is used in an application that requires motor speed adjustment. The speed of the motor at the nominal armature voltage was measured as 1600 rpm. All losses of the motor and voltage source and the effect of armature reaction are neglected. It is accepted that the engine is not saturated.Answer the questions below.a) Draw the armature and excitation circuit of the motor and write the formulas for the equivalent circuit.b) If the load moment of the motor at the nominal armature voltage is 420 Nm, then calculate the armature current and the input power of the motor.c) If the armature voltage of the motor is kept constant at 600 V and the excitation current is decreased until the speed reaches 4000 rpm, then calculate the shaft moment. Show this working area on the M = f (W) axis.
The OCC is measured by increasing the fieldcurrent in steps from zero to some maximum value, and recording the corresponding values of armature emf. If now the current is decreased from maximum to zero, the emf values will be different; why?
Complete solution pls. Thank you
power electronics and drives
Please all subparts
A 100 hp, 1750 rpm, d.c. shunt motor has an armature inductance of 1.15 mH, a resistance of 0.0155 2 and an armature voltage constant of 1.3V.s/rad. The motor is operated from a three-phase half-wave controlled-rectifier at rated armature current of 35 A. Find the firing angle a, assuming that the supply voltage is 400 V and the motor speed is 1750 rpm. Consider the thyristors to have a forward voltage drop of 1.5 Volt and assume continuous conduction.
A de machine is controlled by the step-down de-de converter shown below. The armature inductance La =0.2 mH and the armature resistance can be neglected. The armature current is 5A. The Buck converter is operating at the switching frequency is 30 kHz and the duty ratio is 0.8. L₁ + Answer the following questions: 1) Calculate the input voltage (Va) if the output voltage (ea = 200 V). 2) Find the ripple in the armature current (a). 3) Calculate the maximum and minimum values of the armature current (la). 4) Sketch the armature current (ia (t)) and the supply current (id (t)).
b- Explain why in the design of the iron cored electrical machines magnetic circuit analysis the magnetic characteristics in the first quadrant is considered, while in that of Permanent Magnet Machines the magnetic characteristics in the second quadrant is considered?
Q3/ 4- pole dc shunt generator with lap connected armature has field and armature resistance of 80 Q and 0.1Q. respectively. It supplies power to 50 lamps rated for 100Volts, 60 Watts each of lamps. Calculate the armature current and the generated EMF by allowing contact drop of 1V per brush.