3. The planar truss below is supported by a pin joint at G and a roller at E. Determine the forces in members AB and AF using Method of Joints (MOJ). Determine the forces in members CD, CE, and EF using Method of Sections (MOS). State whether each member is in tension (T) or compression (C). Please put your final answers in the table provided. 2 m B #M E 2 m F 2 m 3 kN G D. 2 kN 2 m 3 m Member AB AF CD CE EF Force (kN) T/C

3. The planar truss below is supported by a pin joint at G and a roller at E. Determine the forces in members AB and AF using Method of Joints (MOJ). Determine the forces in members CD, CE, and EF using Method of Sections (MOS). State whether each member is in tension (T) or compression (C). Please put your final answers in the table provided. 2 m B #M E 2 m F 2 m 3 kN G D. 2 kN 2 m 3 m Member AB AF CD CE EF Force (kN) T/C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The given bridge truss supports point loads of 200kN at joints B, D, F, H, and J. The structure is supported by pin support at the joint A and roller support at the joint I. Determine the member forces AD, CE, CF, FH, GI, and IJ. Indicate whether the forces are compression or tension. Show your calculation steps in detail and write your answers in the box below. 200 kN 200 kN 200 kN 200 kN 200 kN D F В E 7 m 4 m 3 m -5 m -5 m 5 m -5 m
1. Use the METHOD OF SECTIONS to determine the forces in members AC, BC, and BD of the truss in Figure 1 and indicate whether each of these members is in tension or compression. As usual, show any free-body diagram(s) (including all essential components), and clearly annotate all calculations. Note: You may use the support reactions calculated in Tutorial S2, Problem 3 without repeating the necessary calculations. A E 220° 1 m 25 KN B D 1 m 1 m Figure 1. [ans.: FAC = 51.29 kN (tension); FBC = -22.73 kN (comp); FBD = -16.07 kN (comp)]
2 m Roller 2 m 45° 45° A 2 m Pin-Joint 500N 3.1 Determine the reaction forces at the supports of the truss structure. Determine the member forces (FAB, FAD, FAC, Foc, FCD ). Define whether each member is in tension or in compression. Based on your calculations, replace the figure with an equivalent truss structure by removing the zero-force members, if there is any, and sketch its figure (showing dimensions, supports, applied load, 50ON, similar to the figure given above). 3.2 3.3 3.4
1. Use the METHOD OF SECTIONS to determine the forces in members AC, BC, and BD of the truss in Figure 1 and indicate whether each of these members is in tension or compression. As usual, show any free-body diagram(s) (including all essential components), and clearly annotate all calculations. Note: You may use the support reactions calculated in Tutorial S2, Problem 3 without repeating the necessary calculations. А C 220° 1 m 25 KN В 1 m 1 m Figure 1. [ans.: FAC = 51.29 kN (tension); FBC = -22.73 kN (comp); FBD = -16.07 kN (comp)]
The truss structure shown below is subjected to the following loads F - 549 lb F - 839 lb F- 806 lb and has the following geometry: w- 20 ft F2 D F3 B F Determine the support reactions at A and E Determine the forces in members BC, CG, and FG and state whether they are in tension or compression. Determine the forces in members ED and EF and state whether they are in tension or compression.
Q2- Determine the forces in members GE, GC, BC of the truss shown in the figure. ( use section method ) 600N E 6m 6m 6m 1800 N
1) Find the reactions at supports A and E. Also, find the force in each member of the truss and report if the member is in compression or tension. The magnitudes of forces F1 and F2 are 5 and 15 kN, respectively. A,8,C,D,E,6,H,I,J are the joints of the truss B hinge 1.5. 1.5m E roller 4m 4m
Determine the forces in all bars of the truss shown in the given figure. Indicate tension or compression. Given: X= 30 kN. BXKN 60 KN The force in member AB (FAB) is The force in member BC (FBC) is The force in member AC (FAC) is [ 6m KN. KN. kN.
The truss shown is used to support a 11 kg block with a pin at A and a roller at E. Given a = 1.1 m, b = 0.7 m, c = 1.2 m and d = 1.2 m find the Internal forces in members AB, BD, BC and Co. b d A E The force in member AB Is The force In member BC Is The force In member BD Is The force In member CD Is B D C N In (Click to select) (Click to select) N In N In (Click to select) IN In (Click to select) (Click to select) tension compression V V
Find the forces in the members AE, DE, and AC of the truss shown Assign a tension or compression value to each member. Using methods of sections -10 ft- A 14 ft 15 kips B F 5 ft D E 40 kips -10 ft- C GO 5 ft 6 ft ✓ 10 ft
The truss shown is used to support a 11 kg block with a pin at A and a roller at E. Given a = 1.1 m, b=0.7 m, c=1.3 m and d = 1.3 m find the internal forces in members AB, BD, BC and Co. b A E a The force in member AB is The force in member BC is The force in member BD is The force in member CD is B D C N in (Click to select) N in (Click to select) N in (Click to select) N in (Cack to select)
2) A cantilevered truss is loaded as shown below. Using method of sections determine the force in member BC. Leave your answer in terms of P. Specify tension (T) or compression (C). (FYI, you do not need a calculator to do this problem.) (Hint: you do not need to find the support reactions to do this problem.) Ans: FBC = (9P)/4 (T) 6 m 6 m 4 m D E 3 m 6 m 3 m