3. The op-amp shown in the figure below. c. d. 1 kQ Rs e. 1 KQ V₂ Ra 2 km U₁ 2 kn a. Write a node equation at node 1 by summing the currents leaving node 1. Represent V, as a function of V₁ and V₁. b. Write a node equation at node 2 by summing the currents leaving node 2. Represent V, as a function of V₂. Represent V, as a function of V₁ and V₂. Find the numerical value of V, when V₁ = 3.5 V and V₂ = 5 V. Find the numerical value of V, when V₁ = 3.5 V and V₂ = 0 V. OUT

3. The op-amp shown in the figure below. c. d. 1 kQ Rs e. 1 KQ V₂ Ra 2 km U₁ 2 kn a. Write a node equation at node 1 by summing the currents leaving node 1. Represent V, as a function of V₁ and V₁. b. Write a node equation at node 2 by summing the currents leaving node 2. Represent V, as a function of V₂. Represent V, as a function of V₁ and V₂. Find the numerical value of V, when V₁ = 3.5 V and V₂ = 5 V. Find the numerical value of V, when V₁ = 3.5 V and V₂ = 0 V. OUT

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Semi-ideal OpAmps – If we have an opamp with FINITE gain A, solve for the voltage gain Vout/Vin. Recall that the semi- ideal op-amp (finite gain) has the equation, Vout = A(V*-V) No current flows into V* and V. RS 7 Vin Vout OUT R1 6 R2
For all circuits assume an ideal op-amp: 1) For the inverting amplifier shown, calculate a) Vout/Vin b) Zin (impedance "seen" at Vin) c) Vin/Vs d) Vout/Vs (Vout/Vin)(Vin/V₂) Zin R₂ R1 w 2 3 R2 4 V- -15 V 6 Vout
1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
If the ideal design for op-Amp circuit generate 200 mV at the output, Then practically with 26 mV offset voltage the output voltage of the circuit will be equal to .............. mV
Here is a single op-amp, shown under two different conditions (different input voltages). Determine the voltage gain of this op-amp, given the conditions shown. Also, write a mathematical formula solving for differential voltage gain (AV) in terms of an op-amp's input and output voltages. +12 V +12 V Va=1.00 V %3D Vout = 1.5 V +12 V V=1.00003 V %3D -12 V +12 V +12 V Va =1.00 V %3D Vet = 6.8 V +12 V V 1.00004 V -12 V
An op-amp is arranged together with R1, R2 and Rf as shown in Figure Q2. Determine the relationship berween Vout and Vin using the ideal op-amp assumptions. R1 + Vin Vout Rr R2 R1 Figure Q2
Q8 The circuit shown in Figure 4 is a two op-amp instrumentation amplifier. (a) Derive the expression for the output voltage, Vour, as a function of inputs Vin1 and Vin2- Assume ideal op-amps. (b) If R1=R4 and R2=R3, simplify the expression for VouT. R1 Vint Vinz R2 A1 Vot R3 R4 Vx A2 VOUT Figure 4 Two Op-Amp Instrumentation Amplifier
The two input terminals of an op-amp are connected to voltage signals of strength 745µV and 740µV repectively. The gain of the op-amp in common mode is 50 and CMMR is 8&IB. Calculate the output voltage and % of error due to common mode.
Given circuit, assume op-amp is ideal. What is the input resistance of the circuit, RIN? What are the currents in the inputs of op-amp? i-=? i+=? What is the output resistance of the circuit, ROUT=? Find voltage VA and VB? What is the nodal equation (KCL) at node VB? Solve for VOUT=?
Example 07: For the circuit shown in the figure, calculate the output voltage when 1- R1 = R2 R3 = R4 = 100n 2- R1 = R2 = R3 = 1002 and R4 = 1202 Consider the circuit use an ideal Op-Amp and its resistances do not load the bridge circuit. 12K ww 10K 10K 12K 10V
Q3. This question is on op-amps. (a) Comment on the differences between the values in the two columns of properties in the table for both an ideal op-amp and a typical 741 op-amp. Fill in the two missing values. Op-amp Gain Input resistance Unity Bandwidth Short circuit current Output resistance Ideal Infinite Infinite Infinite 0 741 200000 1MHz 25mA 75 ohms
(c) (d) Figure Figure Q1b shows an Op-amp with a bias current compensating resistor (Rp). R₁ V₂. Vp IB. R₂ W A • V₂ Figure Olb (i) Derive an expression for V. to quantify the effect of bias currents IB+ and IB-. [3] (ii) Explain how you would choose a value for Rp to reduce the output error due to the bias currents, IB+ and IB.. [3] Referring to an op-amp define what is meant by common-mode rejection ratio (CMRR) and explain the effect a finite CMRR would have on high-precision applications. [4] Page 2 of 7 Continued overleaf