3. The figure shows a steel bracket bolted to the face of a steel column. Find the bolt size required for a maximum load (F) = 15 kN. Bolts are to be grade 8.8 and reusable. Assume a coefficient of friction of joint of 0.6. Top View Side View 20 1.57 20 50 70 140 co A 260 kolcom Z DX T130 130 YA F=15KN Ans: M12

3. The figure shows a steel bracket bolted to the face of a steel column. Find the bolt size required for a maximum load (F) = 15 kN. Bolts are to be grade 8.8 and reusable. Assume a coefficient of friction of joint of 0.6. Top View Side View 20 1.57 20 50 70 140 co A 260 kolcom Z DX T130 130 YA F=15KN Ans: M12

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A C8X11.5 single channel section is bolted to a gusset plate with M22 bolts. Assume A572 Gr.50 steel and 10mm gusset plate. Find the following values: The design block shear strength of the channel The allowable block shear strength of the gusset plate 30, 65 65 30 60 80 ооо 60 C8X11.5 (AISC Designation)
A MC230x35.6 connected to a gusset plate with 24 mm diameter bolts as shown. The steel is A572M grade 345. If the member is subjected to dead and live load only, what is the total service load capacity if the live-to-dead load ratio is 3 ? 50+ 65 65 T 50 mmt 50 75 65mm O 0 0 0 MC 230 x 35.6
need answer and how to solve thank you
Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown in the figure, Given that e= 30 mm, s= 50 mm, Fy =345 MPa and Fu=402 MPa, caicukato the following 2 L5 x3x % LLBD (two angles, long legs back-to-back) A242 stoel 60 mm e (am) (mn) e (mm) 55 Not area in shoar for a single angle under block shear lailue, Ariv mm? 56. Not area in tension for a single anglo under.block shoar failuto Arit = 57. Norninal block shear strongth in kN of the double angle Use Ups 10, Pn INPUT ALL ANSWERS AS WHOLE NUMBER
Bolts: M24 – Standard holes Bolt Grade: 10.9 Included Steel Grade: S235 Surface Class: C The ratio of the mean installed bolt pretension to the specified minimum pretension 1. And also, hf value will be taken 1. Be careful that the clear distances are given in the Figure. Calculate the design strength Rd. 150x6
2. CENTRICALLY LOADED CONNECTIONS QUESTION # 2: The lap joint of a tension member is shown in the figure. The plate is 252 mm wide and 12 mm thick. The A325 bolts are 20 mm in diameter and the holes are 3 mm larger than the bolt diameter. Steel is A36. It is required to determine the ultimate capacity of the joint based on gross area, net area, and block shear. Use LRFD specifications and assume that live load to dead load ratio is equal to 3.0. A325 Bolts Properties: Fnt = 620 MPa Fnv=469 MPa A36 Properties: Fy = 248 MPa Fu = 400 MPa Figure 2 63 mm 63 mm 38 mm OO 00 ооо t=12mm HE 38 mm ↑ 63 mm 63 mm 63 mm 63 mm 252 mm
Please answer this po, thank you so much!
The lap joint of a tension member is shown in the figure. The plate is 252 mm wide and 12 mm thick. The A325 bolts are 20 mm in diameter and the holes are 3 mm larger than the bolt diameter. Steel is A36. It is required to determine the ultimate capacity of the joint based on gross area, net area, and block shear. Use LRFD specifications and assume that live load to dead load ratio is equal to 3.0. A325 Bolts Properties: Fnt = 620 MPa Fnv = 469 MPa A36 Properties: Fy = 248 MPa Fu = 400 MPa 1.Determine the total service load (DL + LL).
The tension member shown is a channel C12 x 25 of A572 steel with F,= 345 MPa and F,= 450 MPa, is subjected to a service DL= 275 KN and a service LL= 560 KN. Use equation for U. Use LRFD. 65r 65m65 -22mm bolts O O o O C12x25 O O O 0 Check the adequacy of the channel tension member.0
Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size. (b) Determine the bolt stiffness. Q # 3 15KN Rotating shaft Pillow block Metric (ISO) screw (c) Determine the stiffness of the 15 members. (d) Evaluate Yielding, Load and Joint Separation factor of safeties if the joint is permanently bolted. Steel 1cm Som Grey Cast Iron CLO-3, PLO-2
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related beams were provided in Chapter 4 as Exercises 4. I through 4.11. These free-body diagrams constitute exercises that will be used here and again in Chapter 12. Follow these instructions carefully to save time later: (a) On each sheet of engineering paper reserved for analysis, calculate the vertical shear specific to that member at appropriate intervals across the length of the free-body diagram. Be sure to solve for locations where shear passes through zero. (b) On cach sheet of engineering paper containing the tree-body diagram, neatly draw the related shear diagram directly below the associated free-body diagram. The shear diagram should be located in the middle one-third of the page. Reserve the bottom one-third of the sheet for the bending moment diagram introduced in Chap- ter 12. Be sure to show…